Question about Crafts & Hobbies

1 Answer

I am looking for a drive belt for a Geetech CT-345 12" planer. The part No. is HK14014000 & spec no. is 135J-6. Have tried contacting them direct with no response. Reg Beety, email regbee@bigp

Contacting CHIU TING MACHINERY direct & GEETECH. Tried alfred@geetech & katherine@geetech with no response. I really need to get a belt because I recently fitted a spiral cutter head to my machine. Regards, Reg Beety

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Try Oliver Machines. They no longer have the 12" planer but they may have access to part or know who to contact.

Posted on Dec 27, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Belt on my dewalt dw680 planer slips and starts smoking

If the ball bearing of the armature was getting too hot by working with too hard woods may be the bearing of the armature can melting loss the drive belt have lost a little tension by it the housing and a bearing has to replaced in that case.

Feb 10, 2016 | Dewalt DW680K 3-1/4" Planer

1 Answer

I need all manuals for my SAC RS 63-S Surface Planer

Planers - Single - West Coast Machinery
Delta/Invicta RC-63-D 24" Planer in excellent condition. ... Table jack screw sprocketshave been replaced ... 16" single surface planer, - 5HP 208-230 volt single phase belt drive motor, - push ... with operation manual, - excellent condition but offered "as taken from service". ... 2240/440V, three phase S/N 203851 1974 year.Missing: my

Wood working machinery > Planers > Thickness planer (used)
Used Dickte SAC, further information will follow shortly... 2.500 EUR ... Thickness Planer, Thicknesser Huefner & Soehne 63 ... Thicknessing machine Sicar S 500... Working width: 500 mm Working height: 200 mm 2 speeds 2 Table rollers manualtable lift 4 knives - Safety shaft. ... Thicknesser mitTersawelle SAC RS 53Missing: my

Woodworking Planers - Southwest Machinery & Equipment

Dec 14, 2015 | Masonry Tools

1 Answer

This is a follow up to your request for more information regarding a drive belt for my Geetech CT-345 12" Planer.

surfing the net reveals that the planer was made by geetech& chiu and was named to any retailer (GMC,Bosch Talon Masters anybody who would place an order for quantity), and that wanted one. ( go on line for geetech&chiu and read all the stories). What this means that the drive belt you are after will be a generic belt and will probably be available fro reputable machinery repairers, retailers, gearing/bearing shops. What you will need is the belt as a sample so that it can be matched.If you do not have the belt any more then run a piece of string around the pulleys and get a measurement. get a width measurement as well and see if it is toothed or multiple v's

Nov 25, 2014 | Crafts & Hobbies

1 Answer

Replace the drive belt

Do you mean replacing the cutter head drive belt?

With power off start the ribbed belt on the motor pulley, insert allen wrench into cutter head shaft. slowly rotate cutter head while feeding belt onto cutter head pulley. While rotating head, alternate between pulleys feeding it on one rib at a time. Softening the belt in hot water is NOT necessary to install the belt in this fashion.

Complements of


Billy of Hayward Delta 22 560 Type 1 Planer Parts

Sep 16, 2014 | Delta 12" Portable Planer Model 22-560 W/...

1 Answer

I have problem finding a grooved belt for

This is a link to the company that sells the planer, perhaps you could contact them about parts!
Good luck!

Oct 03, 2013 | Makita 1902 4Amp 3 1/4 Inch Hand Held...

1 Answer

Planer problems

If you're looking at the planer from the infeed side, there's a belt guard on the right side of the head. Remove it and check the condition of the drive belt. If it's broke the motor will spin without powering the cutterhead and feed rollers. The drive belt is still available as part number 22-563 on sites like and Just put your model number in their search box and find the drive belt in the breakdown.

Aug 01, 2012 | Masonry Tools

1 Answer


As you may have discovered, Sunhill Machiney is out of Business. Story I have is that the owner is deceased and that the descendents are either liquidating the company or planning to move the company to California, but that is rumor.

Three options:

1. Most of Sunhills machines were made by Geetech. You may have some luck contacting them directly. Geetech

2. The Sunhill operation was/ is in the same building with Oliver. Coincidentally, Oliver also sources many machines from Geetech. You may have some luck contacting Oliver directly and politely asking if they know anything about who to contact for parts or (perhaps) the Oliver machinery may be similar enough that the part you need may interchange.

3. Steel City also offers a 15" widebelt sander. You may have some luck in parts interchange there as well. Steel City customer service

Hope I have been helpful.


Grant in Iowa

Dec 20, 2010 | Garden

Not finding what you are looking for?
Crafts & Hobbies Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crafts & Hobbies Experts

R.A. Ellis
R.A. Ellis

Level 3 Expert

12469 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

20907 Answers

ray gallant

Level 3 Expert

52050 Answers

Are you a Craft and Hobby Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides