Question about Staples Tools & Hardware - Others

1 Answer

How do I load my Rapid Classic 9 heavy duty stapler? I can open the back, and slide out the spring, but when I put the staples on it doesn't seem to work. Thanks in advance!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Staples Master
  • 44,260 Answers

Check the front for jam use small screw driver to get any staples out . but take the spring out of back first

Posted on Mar 02, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 40 Answers

SOURCE: Swingline Stapler Staples Only After You Open It Up....

When you lift up the top of the stapler (as though you are going to put staples in), does the pusher slide freely back and forth? It might be getting stuck at some point and not pushing the staples (either due to a worn pusher spring, or friction). First (after removing the staples) try spraying some light oil on the mechanism and lifting the top part of the stapler up and down a few times and observe how easily it moves back and forth. Also, with the top open try GENTLY sliding back and forth a little - if it slides fine with no sticking, try loading staples and using stapler. If it slides ok, but doesn't quickly return to it's "normal position" when pulled so as to put tension on the spring, rhen the spring may be worn and need replacing.

Posted on Mar 14, 2009

  • 454 Answers

SOURCE: can't load staples in high capacity stapler

Try breaking off about 15 staples from the strip.

Posted on Dec 24, 2009

  • 332 Answers

SOURCE: I have a Swingline Optima Heavy duty manual

You may nave too many staples remove half of them and see it that helps

Posted on Mar 11, 2010

lucian2010i
  • 575 Answers

SOURCE: 900XDN-C SWINGLINE HIGH CAPACITY HEAVY DUTY STAPLER OPERATIONS MANUAL

auto parts store sells a pick with straight on one end and 90 degree on other end.
This should be slender enough to pull staples out.

Posted on Mar 27, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put back together


Stanley Model TR45 Light Duty Staple Gun Review - YouTube

? 3:35
https://www.youtube.com/watch?v=hWmvXhkqnYI
Jul 25, 2012 - Uploaded by Vansvideoreviews
Stanley Model TR45 Light Duty Staple Gun Review ... How toPut Staples in a Craftsman Stapler (Model 968447) ... Stanley SharpShooter Manual Staple and Brad Gun review - Duration: 9:35. by Unpack Guy 35,948 views.

How to load staples into a Stanley Stapler - YouTube

? 2:11
https://www.youtube.com/watch?v=j4Q5W0uKS-s
Mar 26, 2013 - Uploaded by David DeStefano
This video shows you how to load staples into a Stanley StaplerModel # TR110. ... Stanley SharpShooter Manual Staple and Brad Gun review ...

put stanley sharpshooter staple gun back together ... - Fixya

www.fixya.com > Forum > Tags
Find solutions to your put stanley sharpshooter staple gun back together question. ... staples for the TRE500 Stanley Sharpshooter Electric Heavy Duty Stapler.

Dec 10, 2015 | Stanley SHARPSHOOTER HEAVY-DUTY STAPLE GUN

1 Answer

Loading staples into a Stanley sharpshooter staplegun


There are 4 staplers in the Stanley SharpShooter family. You drop the staples on top of the "slide out loader," then slide it into the gun. See models and staple sizes below:


TR150HL Stanley Sharpshooter
  • Stanley SharpShooter TRA700 series or Arrow T-50 heavy duty staples

TR150 SharpShooter
  • Stanley SharpShooter TRA700 series or Arrow T-50 heavy duty staples

PHT150C SharpShooter Heavy Duty Hammer Tracker
  • TRA700 series or Arrow T-50 heavy duty staples (1/4"-3/8")

TR250 SharpShooter Plus Heavy Duty Staple/Brad Nail Gun
  • Stanley SharpShooter TRA700 series or Arrow T-50 heavy duty staples and 1/2", 9/16" and 5/8" Brads

More information on the Stanley SharpShooter and a quick loading demo can be found here: http://www.expotv.com/videos/reviews/12/134/StanleyTR150HLSharpShooterHeavyDuty/185661

Sep 11, 2012 | Stanley Proto Stanley TR150HL SharpShooter...

1 Answer

My rexel stapler does not work, any help[


When you lift up the top of the stapler (as though you are going to put staples in), does the pusher slide freely back and forth? It might be getting stuck at some point and not pushing the staples (either due to a worn pusher spring, or friction). First (after removing the staples) try spraying some light oil on the mechanism and lifting the top part of the stapler up and down a few times and observe how easily it moves back and forth. Also, with the top open try GENTLY sliding back and forth a little - if it slides fine with no sticking, try loading staples and using stapler. If it slides ok, but doesn't quickly return to it's "normal position" when pulled so as to put tension on the spring, rhen the spring may be worn and need replacing.

Sep 11, 2012 | Office Equipment & Supplies

1 Answer

Swingline optima 40 how do you open and close the stapler?


Swingline heavy duty staplers provide the power to staple up to 120 pages of 20-lb. paper easily and consistently. The all-metal construction of these staplers makes them an indispensible office tool. However, the way to load staples into a Swingline heavy duty stapler differs from the method for loading most other manual staplers and can cause a little confusion.
Difficulty:Easy Instructions

    • 1 Remove the follow block at the back of the stapler by pushing the mechanism in, lifting the block up over the holding hooks and sliding it out from the stapler. The follow block is the spring-loaded mechanism that holds the staples in place within the stapler.
    • 2 Load the heavy-duty staples into the staple tray.
    • 3 Replace the follow block by inserting it back into the stapler and locking it into place over the holding hooks.

Read more: How to Load a Swingline Heavy Duty Stapler ' eHow.com http://www.ehow.com/how_5822366_load-swingline-heavy-duty-stapler.html#ixzz1bVwG5bBn

Oct 21, 2011 | Swingline ® High-Capacity Heavy-Duty...

1 Answer

I have a rexel odyssey heavy duty stapler but the spring has popped out, how and where do I attach it back on?


Rexel Odyssey heavy duty stapler: The pring that pushes the staples into position can come losse if the stapler iss dropped. It's difficult to work out how to replace it! However, there are only two "lugs" that will take the circular ends of the spring. One obviously fits to the sliding staple retainer. The other to the back end of the pressed-metal inner body. However, to work, the spring must be threaded from this point along the pressed metal parallel-sided inner body back through a slot and over a rounded bent piece (shiny from prvious friction) and back down to the sliding staple retainer. It's trickey to do, but that's where it has to go in order to provide forward tension when the Stapler is closed.

Aug 02, 2011 | Office Equipment & Supplies

1 Answer

How to load staples?


  1. Remove the follow block at the back of the stapler by pushing the mechanism in, lifting the block up over the holding hooks and sliding it out from the stapler. The follow block is the spring-loaded mechanism that holds the staples in place within the stapler.
  2. Load the heavy duty staples into tray.
  3. Replace the follow block by inserting it back into the stapler and locking it into place over the holding hooks.
Resource 1 : eHow Article

Feb 21, 2011 | Swingline Heavy Duty Stapler 30 160 Sheet...

1 Answer

How do I replace the staples in Stanley Bostitch B310HDS? I cannot seem to figure out how to open it.


"The staples load from the rear of the stapler. At the back end of the is a piece of black plastic that extends beyond the end of the stapler. This device holds the staples inside the stapler. To open the area where the staples are placed, push this extended button and lift up on it. The spring device that holds the staples inside the stapler will then slide out. Place a new strip of staples inside the stapler on top of the two metal guide rails. Then insert the spring device to lock the staples in place. The stapler is now loaded and ready to work. " hope this helps you out

Jan 06, 2011 | Stanley Bostitch 00540: 00540 AntiJam ?...

1 Answer

Instructions on how to load a swingline heavy duty stapler.


You pull up and back on the stapler head. Then pull out the spring that keeps the staples loaded. Be careful as the spring is very strong. Then put in the staples and put the spring back in behind the staples.

Aug 13, 2010 | Swingline Heavy Duty Stapler 30 160 Sheet...

1 Answer

Problem loading gun..Where do we put in the staples and change the dial to accomodate it? fred


The staples should load in through the end of the hammer stapler. The end is spring loaded to push the staples forward, so push the end - usually a crome square - into the handle end then move that part up approximately 1/4 inch and pull back. The spring mechanism should slide out so you can add new staples. These staplers take a specific size of staple and a certain number to allow you to put the spring mechanism back into the stapler. If you do not know the correct size for your stapler someone at your local hardware store can help you find the correct size and they will probably even show you how to load it. Good luck!

Jul 07, 2009 | Ace Hardware Ace Heavy Duty Staple Gun...

2 Answers

Swingline Stapler Staples Only After You Open It Up....


When you lift up the top of the stapler (as though you are going to put staples in), does the pusher slide freely back and forth? It might be getting stuck at some point and not pushing the staples (either due to a worn pusher spring, or friction). First (after removing the staples) try spraying some light oil on the mechanism and lifting the top part of the stapler up and down a few times and observe how easily it moves back and forth. Also, with the top open try GENTLY sliding back and forth a little - if it slides fine with no sticking, try loading staples and using stapler. If it slides ok, but doesn't quickly return to it's "normal position" when pulled so as to put tension on the spring, rhen the spring may be worn and need replacing.

Dec 14, 2008 | Staples Swingline® 36115 Staple Guns Tools...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

481 people viewed this question

Ask a Question

Usually answered in minutes!

Top Staples Tools & Hardware - Others Experts

Kazim ERGUNEY
Kazim ERGUNEY

Level 3 Expert

577 Answers

Jo Ann

Level 1 Expert

20 Answers

magna buff

Level 3 Expert

3828 Answers

Are you a Staples Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...