Question about Jacuzzi Luxura, 530 Whirlpool w/ Integral Skirt - N790/Col

1 Answer

Does the pump on my motor have a reset button

I cant see the far end of the pump does it have a reset button on it I have power to the gfi but the pump wont turn on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jacuzzi Master
  • 717 Answers

There are no reset buttons on motors.
How do you turn the pump on/off ?

Posted on Feb 09, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pump does not turn on. there is power to the board but nothing lights up


No power supply to "board" possibly 24vac, or an air type of control, so that the air supply pump is not active. Possibly the power supply to the pump and control board has "popped" the
circuit breaker. Check, the circuit breaker. There may also be a GFI Ground Fault Indicator that acts like a circuit breaker but is more sensitive, especially near water. Look at the receptacle that the motor plugs into. GFI has a test button and a reset button.

Mar 26, 2015 | Jandy AquaLink RS OneTouch RS8 Pool or Spa...

1 Answer

RE: Friedrich SL28N30B Has Faulty LCDI cord ( will not set -reset ). When plug in blue power light comes on then goes out. Cut cord and installed standard 3 prong male Plug end. Same results- power...


It could be that the faulty cord burned your built in gfi internal switch must like a gfi breaker that gets burn off and never resets . Replacing the cord as you did is a smart move since I would never place an appliance on a gfi receptacle .

May 26, 2014 | Dryers

1 Answer

Jacuzzi Amiga motor does not tuen on. Hardly ever used


There are no reset buttons on bath pumps. It may be the motor is bad or the toggle switch is bad.

US Parts Center

Jan 26, 2014 | Jacuzzi Amiga Whirlpool JAC-N888...

1 Answer

Quit running when I turn the switch on nothing


1- You likely overheated the motor find the small red button on the end of the motor and push it after the motor cools down some
2- You tripped a circuit breaker in the electric panel, go to the panel and look for the breaker that does not line up with the rest of them and move it off then back on.
3- If your outlet has a GFI on it go reset the GFI reset button.

Nov 07, 2013 | Delta Saws

2 Answers

My pump has been acting up for a while now. I turn it on and it runs from a min to an hour and trips itself or the GFI. Yesterday I could not get it to turn on at all. I would push the button and it...


This sounds like you have a bad motor. You should take it to a motor shop and have them check the windings or the bearings. Something inside the motor is causing the GFI to trip.

US Parts Center

Oct 02, 2013 | POL 1500 GPH SFS SkimmerPlus Filter Pump...

1 Answer

When I turn on the pump it kicks off the GFI


COULD BE A BAD GFI, OR THE MOTOR IS SHORTED TO GROUND.. AS A (TEST ONLY) YOU CAN REMOVE THE GFI AND TRY IT, SEE IF IT WORKS

Jun 03, 2011 | Hayward SP15932 PowerFlo Matrix...

1 Answer

I have a kohler bath jet tub. When I push the button the motor tries to start and then trips the gfi breaker. Thought maybe it was the gfi breaker and replaced it. Wasn't it. I took out the gfi breaker and...


Did you try an electric motor rebuilder? $500 seems too high to repair a motor. Motors have either a capacitor or dual windings to get them started and it sounds like yours has failed. Get the numbers off the MOTOR and call a motor rebuilder in your area for pricing.
Gary

Jan 24, 2011 | Kohler Home

1 Answer

Pump plugged in to grounded receptacle trips the


If by "trips the breaker" you mean the GFI then you are leaking current to ground, GFI's trip when there is an imbalance between the current going to the motor on the HOT side and returning from the motor on the NEUTRAL side, if it is tripping the GFI it is likely the sign of a failing motor.

May 27, 2010 | Little Giant WGP-65-PW 1/8 HP, 1900 GPH...

2 Answers

My jacuzzie motor just clicks and won't turn on.


Look behind the tub cover, it should have one. You should be looking for a GFCI it sounds like. These are the outlet that you generally have in your kitchen. They have a reset button and it just sounds like it needs to be reset.

Aug 02, 2009 | Jacuzzi Bellavista 6 Whirlpool w/2-Speed...

2 Answers

Pump trips breaker


If the seals are damaged, water will leak into motor section and cause GFI to trip and yet the pump will seem that it is running fine if plugged into a non-GFI receptacle

May 28, 2009 | Tsurumi Pump s Submersible Trash Pump -...

Not finding what you are looking for?
Jacuzzi Luxura, 530 Whirlpool w/ Integral Skirt  - N790/Col Logo

418 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

Mike

Level 3 Expert

4336 Answers

john h

Level 3 Expert

11057 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...