Question about Audio Players & Recorders
GPlease help me fix thir loaded briefly powers up then overload light appears after Five seconds
If the receiver works at low volume, but goes into OVERLOAD and shuts down at higher volume, it means you are player the unit too long and too loud. Try yo keep the volume down to a reasonable volume.
Posted on Aug 08, 2015
Remove top cover, then find access to the fan,,3 fast locks to chassis. Remove fan and resolder 2 fan terminals, and with plenty solder and flux... Clean up your mess , reinstall fan, making sure that fan and mating connector pins contact.Bend chassis contacts, resolder both contacts to ensure good electrical contact Turn on amp with bass boost on and Stereo mid range , Notice that the fan turns on with high output levels... This is a typical cooling fu from Technics´design.
Posted on Sep 05, 2017
If you have the skills, these technics amps are known to get bad solder connections on the amplifier ic's and voltage regulators. You can access these points through the bottom access panel. Look for any fish-eye solder joints.
Posted on Sep 01, 2015
Overloads are often caused by short circuit conditions on speakers or the wires to them. Remove all speaker wiring and then try powering up. If the overload light continues to come on you might have blown something on the main amp board, such as a power transitor, that was caused by bad wiring or speaker problems.
Posted on Nov 18, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Tecnics SU-G95 stereo overloaded
Power down,disconnect the speakers and power back up. If it still say's overload, it needs to go to service. If not, check your wires, connections, and speakers one by one to hunt down the problem and correct. Hope this helps
Posted on May 25, 2009
hello ive got a diffrent problem ive got a technics hifi and when u put it onto aux it says txe-rvc and cd is dc its all the wrong way around what can i do thanks
Posted on Aug 29, 2009
Are these resistors near or linked to whatever is on the heat sink? If they are then they are bais resistors and they have burned up due to a fault on the devices on the heat sink.
Resistors are cheap, all you need to do is find out what value they are. This is part of the colour code. However if they are burned then you might not be able to read the code! So you will need the circuit diagram or someone to tell you the value.
The problem however will be if whatever on the heatsink has gone!
It could be an IC since you have lost both channels, unless you have shorted the speaker wires of both channels somehow and blown both right and left amps!
Posted on Nov 27, 2009
SOURCE: Technics SU-G91 OVERLOAD PROBLEM
I just bought a Technics SU-G91, hoping to connect to my akai GX-230D reel to reel and speakers. do I need to get anything else to hear it, like a receiver/tuner? everything appears to be working or have I just hooked it up wrong?
Posted on May 31, 2013
Tips for a great answer:
Sep 21, 2015 | Technics SU-G75 Amplifier
Nov 15, 2014 | Audio Players & Recorders
Aug 28, 2014 | Audio Players & Recorders
Jan 13, 2014 | Technics SU-G75 Amplifier
Nov 07, 2012 | Technics SU-G75 Amplifier
Dec 27, 2009 | Technics SC-DV290 System
May 25, 2009 | Technics SUV500 2-Channel Amplifier
Jun 19, 2018 | JBL Audio Players & Recorders
Jun 18, 2018 | Harmon Kardon Harman Kardon Soundsticks...
509 people viewed this question
Usually answered in minutes!