Question about Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television

3 Answers

Timer light blinking

Age of WD62725 - 3 yrs
Lamp life: less than 4k hours
Supply Source: connected to Monster Power HTS 1000 Power Center
Problem: Timer Light Blinking system shut down
Reset worked first two times, but after ~ 1hr of use in between shutdowns the picture would begin to 'flutter' and the system would shut down after a minute or two of this. After the second time I kept the system off.
Manual says obtain a line conditioner or power surge protector, but as I mentioned above I have one. I tried separate house circuits, but same results.
Could it be the power supply of the TV and, if so, how much is this and is it worth it?

Posted by on

  • 1 more comment 
  • FixMe2 Dec 09, 2007

    I have a blinking timer light. This problem occurred about 2 months ago and was resolved with the reset button. Unfortunately, the problem has reoccurred and the reset buttom has no effect. No sound, no picture.

  • martsk Jan 04, 2008

    I have exactly the same problem. I lost power for a couple of days and now that it is on my tv timer button just blinks. I cant seem to reset it at all. It won't power up.

  • rick gajin May 04, 2008

    Hi I have the same Timer light blinking problem I change the 4 caps on power supply board but problem still dear

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 80 Answers

Check C81A2, C81A3, C81B3 and C81B4 (1000 uFD, 16V, 105C) on the DM PCB.
Check C8F19, C8F21, C8F22 and C8F27 (1000 uFD, 16V, 105C) on the FMT PCB.
If any are bad, replace all of them with part # 181P734030 (680 uFD, 16V, 105C).

Posted on May 22, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wh I turned on my Mitsubishi WD-62725 the green timer light keeps blinking but no picture. The reset button dose not solve the problem. Bulb is only a few months old. Do you have instructions on how to check/replace power supply and capacitors?

Posted on Sep 13, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 208 Answers

Most likely bad caps on power supply bd. We have had the most problems with the 2 3300 uf caps. but there are 4 1000uf caps that can also be a problem. The main concern is to get to this power supply requires a great deal of disassembly and may require a qualified Mitsu tech.

Posted on Feb 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sony tv blinks red light three times then pauses and blinks again


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/

Nov 19, 2015 | Focus Camera Sony KDL70W850B 70-Inch 1080p...

1 Answer

I am trying to charge my PSX. The Charge light just blinks and it is not charging. What is wrong?


Those have a 1 year warranty so depending on its age it is probably due for replacement.
They should be charge once a month or after each use.

Dec 17, 2014 | PSX-2 Rugged Hi-Power 1000 Peak Amp...

1 Answer

Montster Power hts 350 power conditioner


it depends on where it is and where to find a bulb may have to contact the company itself

Jan 04, 2014 | Monster Power HTS 3500 MK11 Home Theatre...

1 Answer

Monster hts 1000


If half the plugs are not providing power, the most likely explanation is that the ON/OFF switch is in the OFF position.

In this position, the Unswitched outlets will stil be powered, but the Switched outlets will be OFF.

Jan 01, 2014 | Computers & Internet

1 Answer

My monster power HTS 1000 has a loud buzzing sound, should it be replaced ?


take it back to the sort where u bought it from and they should replace it with a new 1

Aug 10, 2010 | Monster Power PowerCenter HT 1000...

3 Answers

I have an RCA RT2500 audio-video surround sound receiver about 10 years old. For the second time in its life, a power fluctuation has knocked it out of service. The standby light comes on, but no power to...


Hold down the power button and unplug the unit. Now release the power button. Plug the unit back into the wall. Now press the button. The system should power up.

Oct 22, 2009 | RCA RT2500 System

1 Answer

Green timer light blinks fast after power loss


If this is a Mitsubishi you have a problem on the dm board, if it is a wd series there are some capacitors that buldge on the top that can cause this, if it is a ws series then you usually have to have the dm board replaced.

Aug 23, 2009 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Sony cineza vpl hs51 projector won't project


Something I found interesting from the internet - lamp life isn't when the bulb dies, but when a bulb has lost 10% of its brightness - so you might well be able to reset the timer and get much more use from the bulb - the image just wont be as bright.

The lamp may not have been changed - just the timer reset - How many hours has the lamp really done - 1000, 3000, 5000?
If you know that the hours are genuine, then was the quartz bulb contaminated with a touch of oil from skin contact?
This will substantially shorten lamp life, due to the quartz going milky and opaque.
The easiest way to check, is to pull the lamp and have a look at the bulb.

If need be replace the lamp and reset the lamp timer.

These instructions are for a Sony Cineza VPL HS3, but may be the same for the HS51
1st thing to check - is the cover properly/completely closed - this can stop the projector from working.
Connect the power and set the projector to standby mode.
Press these buttons on the remote control in this order, for less than 5 seconds each.
Reset - Left Arrow - Right Arrow - Enter

Dec 07, 2008 | Sony Projector Lamp for VPL-HS51

1 Answer

Monster power hts 2000 mkII


Usually the clicking sound is when the unit switches from powering the devices attached and charging the batteries, do the devices attached to the ups still function?

Feb 18, 2007 | Monster Cable PowerCenter HT 1000 (109091)...

Not finding what you are looking for?
Mitsubishi WD-62725 62" Rear Projection HDTV-Ready Television Logo

518 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1213 Answers

The Knight
The Knight

Level 3 Expert

75157 Answers

Jaime Hernandez

Level 3 Expert

2334 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...