Question about Televison & Video

1 Answer

Tv bord fuse damage replace the same type again damage what problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 6,702 Answers

A fuse does not trip to annoy you. It trips because the circuitry is taking to much current. This can be just a little to much, taking it to trip after a few minutes or hours, or lots to much, tripping as soon as you switch on. Can be caused by a defective semiconductor, or a capacitor with a shortage. If you can't see anything wrong on the board, like a capacitor, wilt a rounded head, or a burned out semiconductor or even a resistor, you have to find out by measuring what could be wrong. Without the skills, don't even go there. It could be dangerous because of the high voltages in the TV.

Posted on Nov 09, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung LCD TV 42 blows the 6.3a fuse located next to the plug as soon as you apply power?


You have to change the power supply bord. If fuse blows off then the smps driver section is faulty. Also there is possibility of faulty MOV . MOV metal oxide verister use as a protection device. It would look like a polisher capacitor.. if it's short the you can try to replace it..
If you want to know more about MOV the you can find details in the Internet with photos.
If you need to get some more information about repairing television then check the link bellow http://electro-medical.blogspot.com/

Sep 22, 2016 | Samsung Televison & Video

1 Answer

Chassis cp 79b lg tv bord on but go to sut down eht but audio ok chanal ok no vartical volt +14 -14 crt volt 200 Tv is on poition


Check and replace damaged component/s at its horizontal scan output section circuit. Check the LOT (Line Output Transformer) too for damage. Replace the horizontal scan output transistor. Check the input voltage to LOT. If the voltage is absent check the feeder resistor; if any. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
Type in this key phrase " my service table today " in the search box at the top right of the display window, to get gathered some pages which has the details of practical experiences to the author of that site.

Sep 23, 2015 | LG Televison & Video

1 Answer

65h84 toshiba wont power up after 30 min power outage.


hi Aaron,

please check power button,
bridge rectifire,
bleeder resistor or big cement resistor closed to power input area,
smoothing cap charged to 300v (i assume your power grid is 220v),
when you plugged in and it is not discharging for few min.that means power supply not starting up.
check the power supply bord for any phisical damage burn marks etc...please do the check and come back.
regards,
nuwan

Jan 08, 2014 | Televison & Video

1 Answer

Usp440m-42lp power supply problame


Check its main rectifier diodes. If any of this is shorted, this type of fault can occur. More to say, when you repair power supply regulator board, you should check all the other components too for damage.
google.com/+GopakumarGopalan

Dec 01, 2013 | Televison & Video

1 Answer

My philips 14 inch tv is not working the capacitor 400v was explode and i change it i clean all the chemicals that were on the borde abd the fuse is new what can i do?


I would blanket change the power supply if it isn't working. The electrolyte is conductive and will do an awful lot of damage.
By your description "400v" I presume you mean the main smoothing capacitor, in which case the power supply has been drawing excessive current to make the capacitor leak so I would look next at the line output section.
Hope that helps.

Mar 03, 2011 | Philips 14PT1356 14" TV

1 Answer

How too replace fuse


there are too types of fuses used today there are glass and thermit if its glass then simply remove the cover of the amp find the fuse and replace with new one if you look around and cant find a glass fuse then it has a thermit fuse and they are solded to the bord and really need to be replaced by a tech however if you can solder then email me and ill send you a diagram on what to look for and go from there

Jun 25, 2010 | Technics SA-AX530 Receiver

1 Answer

Usb not reconnigation


if usb is not recoginize click on my computer then hardwere then click device manager. look usb softwere is stall or not ? if stall . keep a other usb card in pci slot in computre(mother borD) iblemt means your bord usb system may be damage. in our jeneral practis we face 945 gcr bord are damage many .time. so i like to say if driver not shown your bord usb hardwere system may be damage.

Jul 14, 2009 | Intel D945GCCR Motherboard

2 Answers

Power does not come on


i have had this problem time and tim again with the cyberhome dvr 1600 dvd recorder its not the fuse thats the problem the converter on the power board is blown i have 7 of these with exactly thesame problem to fix it all you need is a new power board if you unscrew it and take the top off then the power bord is to your right hand side big long board where the mains plug in all you do is once you got a new power board unscrew the old one and screw the new one in and plug the cables back in boo it works and by the way i had 7 of these plugged in when lighteing struck and its the same problem with them all

May 19, 2009 | Cyberhome DVD Recorder - DVR1600

2 Answers

Won't turn on


Follow AC cord in to clip-in glass fuse....replace with SLOW
BLOW 6.3 amp ( T-type) Panasonic factory correction...T.

Dec 19, 2007 | Panasonic CT-32SX31 32" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74185 Answers

Cindy Wells

Level 3 Expert

5123 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...