Question about Zanussi Dryers

Open Question

<!-- from fixya rte -->My Zanussi ZDC 77570w won't power on - Zanussi Dryers

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

timblodgett
  • 691 Answers

SOURCE: My Zanussi ZDC 37200W has no power

Go to the self help section of repairclinic.com Enter you model number for specific trouble shooting advice on your appliance.

Posted on May 14, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Zanussi ZDC 37200W has no power


Go to the self help section of repairclinic.com Enter you model number for specific trouble shooting advice on your appliance.

May 14, 2015 | Zanussi Dryers

1 Answer

Power is on board of my Zanussi ZDC 68560W but machine doesn't show any sigh of life


Electric dryer no start does nothing
Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage.

CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING.

NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position.

If you hear a humming/clicking sound from motor area you more than likely have a bad motor.
Try this test out to see if u have weak windings or relay/capacitor on motor.
Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings

Another thing to check is the belt safety switch. With a multi meter.
Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released.

Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad.

https://www.youtube.com/watch?v=sTRP6kHqAFs
Hey GOD IS GOOD !!!!

Jan 07, 2015 | Zanussi Dryers

1 Answer

Zanussi tumble dryer zdc 77570w


Sounds like the condenser is your problem but, not positive because I have never dealt with these types of dryers.

Aug 27, 2014 | Washing Machines

1 Answer

Zanussi zdc 67550w tumble dryer stopping after 10-30 seconds of the cycle


See if it is overloaded or the clothes are excessively wet... Take out 1/2 the clothes and try again.

Jan 12, 2013 | Zanussi Dryers

1 Answer

Zanussi progress 1200 won't take softener into


Hi there
Now I am urprised. There must be three dispensers in your Zanussi as in my Candy.
One is for the main wash another for prewash and the third one for
the softner.
Look in the manual.
Kolbrun

Feb 26, 2012 | Zanussi Washing Machines

1 Answer

How to use my condenser dryer zanussi zdc 47100. do i fill the bottom bit with water or leave it empty ? just bought it second hand but has no manual !!


this is a drier ? and therefor no water is needed however you will need to ventilate to outside via the conveluted white hose that fits to the machine to prevent the damp exhaled heat fro machine condensing in the room dryer is positioned

Nov 27, 2009 | Zanussi Dryers

1 Answer

How to fix a belt on zanussi tumble dryer model number zdc 46130s


heat elemet works, drum will not tumble. Help. Little odl aldy, Rosemarie

Jan 25, 2009 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dryers Experts

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

Are you a Zanussi Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...