Question about Office Equipment & Supplies

1 Answer

I need to reset oki c9500 to factory settings

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Dedicated:

    Visited the website for 20 consecutive days.

  • Master
  • 817 Answers

Http://my.okidata.com/man-ml320-1turbo.nsf/MOCContents/029CDD66B74320C385256A6B004EE4FE

Posted on Nov 08, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
flopez
  • 161 Answers

SOURCE: Oki C9500 makes VERY LOUD clunking noises but prints fine...

The sound is most probably from one (or more) of the drum units. You can check by taking them out and trying to run the visible gears by hand. If you have spare drums, change them one at a time until you find the defective one.

Posted on Sep 26, 2007

ginko
  • 19396 Answers

SOURCE: oki c9500 fuser

If you need replacement here you find some offers:

Okidata Fuser Unit 120 for C9300 C9500 ... $189.72 - pcRUSH OKI 41946101 Fuser Unit 120V ... $160.83 - PROVANTAGE Okidata C9300, C9500 Fuser Unit ...

Posted on Aug 08, 2008

  • 1 Answer

SOURCE: OKI C9500

We had this issue and removing the optional hard disk fixed it for us, I'm guessing it was on the way out and wasn't really being used so it will not be missed.

Posted on Nov 19, 2008

pineworks
  • 4041 Answers

SOURCE: need to know how to reset the oki c5400n to

Procedure:

  1. Power ON printer while holding both the "+" and "-" buttons until “OKIUSER” message apear in LCD.
  2. Press ""+ or "–" button until “ENGINE DIAG MODE” is displayed
  3. Press "ENTER", will be displayed "DIAGNOSTIC MODE XX.XX.XX S-MODE"
  4. Press "+" or "–" button until “NV-RAM INITIAL” is displayed
  5. Press "ENTER" again
  6. Appear "TABLE 1" message
  7. Press "ENTER" until "EXECUTING RESET" message appears. "NV-RAM INITIAL" message will BLINK... IT resets TONER, DRUM, FUSER and BELT...
  8. Power OFF printer, wait 10 sec, and power ON again

To access Service Mode in C9300:
  • Power ON printer with 0, 1, 6, 7 at same time...

Posted on Jan 30, 2010

  • 1 Answer

SOURCE: I have a Oki C9500 laser, the magenta print is streaky

I have the same problem with my OKI c3100, please help

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oki data c9500 job offset home error


Where the paper exits the printer you will see 3 black sensor arms hanging down. 1 is the exit sensor and the other 2 are job offset sensors. On of those 2 will be stuck. Just gently free it and all should be well.

Jul 16, 2017 | OKI Office Equipment & Supplies

1 Answer

Where does oki c9500 waste toner box located


Your printer does not have a waste toner bottle. Waste toner is stored within the transfer belt. When full it will give you an error indicating its time for a new transfer belt.

Jul 08, 2017 | OKI Office Equipment & Supplies

1 Answer

My OKidata c9500 makes a loud clicking sound when I try to print. Like a drum turning and maybe the contact is not


Similar problem in other Oki's

It's not a drum, I would check the ITB Belt. Known for binding failure.

Okidata didn't spend a whole lot of money/quality plastic/nylon bushings and parts associated with the drive roller and other associated part for their ITB Belt assembly.

I hope this helps,,,Steve

Oct 12, 2014 | Oki Electric Industry Okidata Corporation...

1 Answer

I have a Oki C9500 laser, the magenta print is streaky


I have the same problem with my OKI c3100, please help

Jan 13, 2010 | OKI C9500dxn Led Printer

1 Answer

OKI C9500


We had this issue and removing the optional hard disk fixed it for us, I'm guessing it was on the way out and wasn't really being used so it will not be missed.

Oct 30, 2008 | OKI C9500dxn Led Printer

1 Answer

Color registration problem for Oki Data C9500


Brain-storm .... simple solution .... REPLACED Magenta Drum.... works as good as usual, but is still and always been out a little - very strange, depending on the stock, if I'm using a 10pt coated stock, color registration has always been a little out ( when the cyan and magenta are being used ((together)) - purple - dark blue etc ...)

Mar 31, 2008 | Computers & Internet

1 Answer

Oki C9500 Printing Problem


Check the LED Head and LED Connection. The LED heads are interchangeable, BLK, Cyan, Magenta, Yellow.

Feb 15, 2008 | OKI C9500dxn Led Printer

1 Answer

Oki C9500 makes VERY LOUD clunking noises but prints fine...


The sound is most probably from one (or more) of the drum units. You can check by taking them out and trying to run the visible gears by hand. If you have spare drums, change them one at a time until you find the defective one.

Sep 04, 2007 | OKI C9500dxn Led Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

k24674

Level 3 Expert

8073 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

yadayada
yadayada

Level 3 Expert

80668 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...