Question about Garden

1 Answer

Drive belt on LT150 John Deere Lawnmower. Replaced drive belt recently and tractor will not move at high speed (hydrostatic trans) petal pressed all the way down. Will move slowly (very slowly) but

Replacement belt used: M144044 for Hydro Trans

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,494 Answers

Adjust the belt must be to loose.

Posted on Nov 08, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 188 Answers

SOURCE: I need a diagram of the drive belt for a John

WD 40 might release it and long nose plyers.

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: john deere runs then stops

I fixed my mower stalling issues on the L111 by loosening the gas cap. I ultimately drilled a hole in the gas cap and screened the hole. Sounds ridiculous but without that venting the engine would run approximately 20 mins and die. It was also much more difficult to start the next time. Something else to pass along to whomever might view this... I replaced the cranking battery with a battery that had allot more cranking amps and I no longer had hard start issues ( this was after I vented the gas cap). Hope this helps.

Posted on Aug 11, 2009

  • 1 Answer

SOURCE: Belt change on a hydrostatic 265 John Deere

Instructions for changing main drive belt on John Deere model 265

HELP !!!!!!!!!!!!!!!!!!

Posted on Aug 28, 2009

mickey813
  • 472 Answers

SOURCE: John Deere CR125 hydrostatic mower, engine runs

sounds like you have carb problems

Posted on Oct 15, 2009

  • 420 Answers

SOURCE: john deere 300 garden tractor hydrostatic drive will not work

check two things, make sure the by-pass rod is pushed all the way in and the drive belt from the engine to the rear end (tranaxle). If both check out ok do not attempt to service the tranaxle at home. have thet serviced by a dealer.

Posted on Jun 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Hydrostatic transmission on my Lt150 mower is making a screeching noise when I push on the forward/reverse pedal. The mower will move very slow then stop. It is not the drive belt!


Check trans. oil for debris and quantity. If level is low try topping up first and if this works it would pay to disassemble in the near future, clean the oil filter and fill with clean oil.

Oct 01, 2014 | John Deere Garden

1 Answer

John deere sabre 2354 hv moves slow forward, even slower in reverse


this hydrostat drive tractor is designed to max at 5.5 mph forward, 2.5 in reverse, check linkage at pedal if you dont think your achieving those speeds

Mar 23, 2013 | John Deere 420,1020,2010,2020,2510,2520...

1 Answer

Why do my john deere445 moves at half its speed even when petal push all the way down


is the belt slipping?is the linkage points loose and the pedal doesn't have full travel the rod should have some adjustment to take up the slack

Aug 17, 2012 | John Deere Garden

1 Answer

My john deere L130 with hydrostat won't drive,eng is fine


did you knock the drive belt off?did you pull the lever that allows you to push it when not running?

Aug 15, 2012 | John Deere Garden

1 Answer

John deere 300 garden tractor hydrostatic drive will not work


check two things, make sure the by-pass rod is pushed all the way in and the drive belt from the engine to the rear end (tranaxle). If both check out ok do not attempt to service the tranaxle at home. have thet serviced by a dealer.

Jun 02, 2010 | John Deere 420,1020,2010,2020,2510,2520...

1 Answer

Belt change on a hydrostatic 265 John Deere


Instructions for changing main drive belt on John Deere model 265

HELP !!!!!!!!!!!!!!!!!!

Jul 12, 2009 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

roeb

Level 3 Expert

603 Answers

john h

Level 3 Expert

12650 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...