Question about Washing Machines

1 Answer

What is error code E57?

First wash went ok without clothes, next wash with 7 kg of clothers, machine stopped in a middle of program and still dirty water inside. Shut down machine and try again --> waterpump runs 2 times and then program not starts. Got water out manually, added base water, started again same problem. Pushed 2 buttons to get error code into the screen which is E57? Any ideas how to continue? Machine is 2 days old and i don't want to wait 3 days to get guarantee fellow to see same problem and diagnose issues, then 1 week to wait spare parts etc. Any idea which might be a problem with this brand new machine?

Posted by on

  • Mike Mayers
    Mike Mayers Nov 07, 2014

    AEG Lavamat, Model: LM8548OF, Type: FLI0641B3, Serial: 412 00017

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

E57 Checksum failure Software error occurs - checksum failure. Non-recoverable error. Main control board must be replaced.
:(

Posted on Nov 07, 2014

Testimonial: "Thx, both inverter and mainboard needs to be replaced."

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 156 Answers

SOURCE: Kenmore wash macine

its in your cold water line valve to the washer if it works good with hot water the valve are incoming line being blocked when you turn it on the pressure comes in fast then when pressure is gone water slows down so when its off the pressure builds back up it runs fast then slow

Posted on Feb 27, 2008

  • 1 Answer

SOURCE: samsung smart wash b1245s doesn t work

motor brushes are worn and nead to be replaced easy job if you turn washer on to its side remove the 2 screws at the bottom and take off the plastic panel you can see the motor and the brushes are red plastic bits remove them and replace with new ones that should sort out the problem and cost about £25.00 to do .

Posted on Jun 27, 2008

  • 417 Answers

SOURCE: Zanussi ZWD1680W Front Load All-in-One... Problem:

With the symptoms you describe i would suspect a intermittent heater element fault as you are getting earth leakage current which is tripping the whole supply rather than a current overload which would just trip the socket circuit breaker. Get the heating element checked over first as this is the most likely cause.

Posted on Nov 04, 2008

JR JR
  • 116 Answers

SOURCE: Kenmore Elite he3t model 11045972404

POSSIBLE COMMUNICATION PROBLEM BETWEEN MAIN AND MOTOR CONTROLLER

Posted on Nov 30, 2008

  • 1 Answer

SOURCE: Front Load Washer - Error F30

my maytag mdg5806 aww

just works few second and then goes
can help me?

Posted on Sep 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Elextrolux EWF168540 W TimeManager 8kg stopping mid program without any error message


The recurrent problem may be due to a defect in the Time Manager.

Feb 01, 2017 | Washing Machines

1 Answer

It only wash & don't spin? Then it stops and leak water by the door....


LG Washer & Dryer 7 (WD12331AD)
Its is a direct drive front loader with 7kg capacity for washing and 3.5kg capacity for drying.

when new
thats 7 kg with wet clothes and water
and only 3.5 kg wet clothes to dry

the older it gets the less weight it can wash and dry

worn motor or drum overload if it doesnt want to spin at all

leak at the door . replace the door seal ..is a most common fix

extra info
It has 9 preset settings, 400 - 1200 RPM, 5 temperature settings, digital display and delayed start timer.






26286955-m1yuy1loarf5tbt315tzgxva-1-0.jpg

Sep 20, 2016 | LG Washing Machines

1 Answer

What does error code E57 indicate?


E57 means that your inverter board is drawing too much power' below link shows where and how,
press the helpful button


GE Front Load Washer Inverter Removal

Jan 25, 2016 | Washing Machines

1 Answer

HOW TO UNLOCK THE DOOR TO MY WASHING MACHINE?


Make sure that it is on stop program.
Turn it off and wait a couple of minutes until the safety lock is unlocked.
Then should be ok to open, refer to user manual.

Nov 30, 2015 | Hotpoint Aquarius WDL540P White 60 cm...

1 Answer

I have a Daewoo washing machine DWD-F1011 S, 7 KG..IT STOPS AND gave us an error with code E8.. HOW CAN WE SOLVE IT?


this is what I found E8 Washing machine motor error detectedA fault has been detected with the main drive motor.
  • Check motor connection block
  • Abnormal loading condition

Mar 13, 2015 | Daewoo Washing Machines

1 Answer

Bosch logixx 8 E57


Circut board of the motor is demeged.if you take out the board witch is next to the moyoryou will see on the electronic print
The demeg.

Nov 20, 2013 | Bosch Logixx WAS2446 Front Load Washer

1 Answer

Electrolux Inspire 7 kg washing machine. Error code 22. A program run for 30 minutes Ok and the stop and reset the program. What means e22 and how can be solved? Thanks in andvance!


Hello Serban Alexandru - Typically error code E22 indicates that the water is not pumping out fast enough. Does the drain pump make a humming noise? If so, there may be a restriction in the drain line or siphoning. Otherwise since it is such a complex unit I would recommend contacting a professional to have the pump, timer or main control board diagnose.

Oct 04, 2012 | Electrolux Washing Machines

1 Answer

F&P GWL11 Washer Stops at rinse - Error Code 37


I hate to say it but it sounds like the controller. I used to have one that had a similar problem that was fixed with a diverter and a controller. Another year or two later it was doing the same thing, so we just replaced it. Just a warning.

Jul 08, 2012 | Fisher and Paykel Washing Machines

1 Answer

I have a MAV3700AWW 10.1 kg Washing machine. It does not matter what cycle i use error code UN keeps happening recently. The clothes keep getting tangled on the blade.Please advise.


From what ive read and seen with that error code its a unbalanced load. Makes sure cloths are balance out right and make sure the machine isn't over loaded.

Jan 06, 2011 | Maytag Washing Machines

6 Answers

Fisher and paykel 7.5 smartdrive washing machine, no power


If there is power and all your lights are lighting up but you get no responce from the machiene eg no spin, water filling, wash cycle or drain then it will be the sensor for the lid it will have coroded but this is an easy fix , I hope this helps

Feb 20, 2009 | Fisher Paykel Eco IWL16

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

730 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Brad Brown

Level 3 Expert

16174 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...