Question about Televison & Video

1 Answer

Pioneer sdp4682k i just got a pioneer sdp4682k projection tv ,i plugged it in ,screwed in the direct tv cable into anteena a put the tv on channel 3 and got nothing but snow i went to setup and and had it to autoset all available channels,still nothing help!

Posted by on

  • Anonymous Nov 17, 2008

    i need to replace the board how much does it cost and what is aboard?

×

Ad

1 Answer

Try the RGB or the S-video out of the Direct TV receiver.

Posted on Jan 02, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I JUST GOT A D52W20 HD TV.I SCREWED THE CABLE CONNECTION TO THE ANTENA INPUT. THE ONLY STATIONS I GET ARE LOCAL CHANNELS BUT NO CABLE CHANNELS. WHAT DO I HAVE TO SET ON THE TV OR WHAT DO I HAVE TO PRESS ON...


Before you bought your new TV, was the cable connected to an older TV, and was it working?
When you say you screwed the cable connection to the antenna input, did the cable come directly from the wall, or did it go through a cable box first. If it came through the wall without a cable box, it's possible it's not an active cable account, and you're only getting over the air signals for your local channels (and nothing through the cable). Or, your cable signal might have been analog only, and with the transition this week to digital TV, maybe you're no longer getting the channels broadcast properly.
If you are a cable subscriber, then this problem should be reported to the cable company, and they can do further testing to see what's wrong with your signal.

Jun 18, 2009 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

I have no idea how to get channels to tune in.


In order to get a picture of what is going on you must understand what is happening. The cable box converts all channels to channel three or four depending on what it was intitially set on. That means that you have only one channel coming into the tv. So you cannot program the set. You just have to put the TV on Channel 3 or 4 and leave that alone. Do not try to program the TV. Then change the channels on the cable box. The hitch is that there are several ways to hook a cable box to your set. One is with the RF connector, which is the screw on one, into either Antenna A or B. and the other is through the AV cables which are yellow, red and white. Yellow for video, red for right audio and white for left audio. If your box is hooked to the AV input then you must use the INPUT button on the tv to select the proper AV input. On that set there are several.

Sep 19, 2008 | Mitsubishi VS-50604 50" Rear Projection...

1 Answer

No audio or video


Hi,

If you can see the channel number as well as the volume setting when you press on the appropriate buttons on the remote, then it would seem that what happened is that your TV went into muting (video and audio). This can only be brought about if the TV is not receiving any signal from your cable or aerial. This is a built-in feature. Another possibility is that the tuner section of the TV has some issues. To determine whether cable or tuner, pls try installing a known operational VCR and play a good tape. Connect the RF OUT of the VCR to the CABLE/ANT IN of the TV. Select channel 3 or 4 and should you be able to watch the tap video, then you have just confirmed that it is your cable (or aerial). If on the other hand there is likewise no display on either 3 or 4, then you have just confirmed that somethings needs to be done internally in the tuner section.

Hope this be of some help/idea. Pls post back how things turned out or should you need additional information.

Good luck and kind regards.

Feb 05, 2008 | Pioneer SD-P50A5-K 50" Rear Projection...

1 Answer

Pioneer projection tv model sd-p404


In menu go to cable/then press auto programming see if this fixes your set.

Dec 06, 2007 | Pioneer SD-P50A5-K 50" Rear Projection...

1 Answer

New anteena.


Honestly, There most likely right. It happens more often than you'd think. Try unplgging the brain for a minute with the power off then turn the radio back on after youv'e plugged it back in. It may just need to reinitialize but I doubt it.

Nov 28, 2007 | Pioneer SIR-PNR2 SIRIUS Radio Receiver

1 Answer

Programming digital channels


The problem is not with your TV. You need a digital box to unscramble the channels.

Oct 28, 2007 | RCA HD52W56 52" Rear Projection HDTV

1 Answer

TV/SAT Video channel went out - Pioneer VSX516


Double check the video connection cable directly out of the SAT reciver and the video cable out from the Pioneer reciver, as there maybe an intermittant connection in them. If you replace them or sub them for known good ones, and you still have this probem, there is a switching IC inside the pioneer that has to be replaced.

Jan 04, 2007 | Pioneer VSX-516-K

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75178 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Cindy Wells

Level 3 Expert

5346 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...