Question about Panasonic PV-C2010 20 in. TV/VCR Combo

1 Answer

Standby problem panasonic m# tc-14p2se

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: standby problem

My panasonic tc-14p2 se has a very weak sound i already change the amplifier ic which is AN6265 but still the same problem?

Posted on Nov 22, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I can not scan the tv with digital antena

Product Detail

Just click on the owners manual tab to download manual.

Sep 12, 2014 | Panasonic TC-15LV1 15 in. TV/DVD Combo

1 Answer

My Panasonic. 27 inch triple play will not turn on and the on timer indicator keeps flashing yellow

The unit is either in shutdown (self protection) or the unit is not making it out of standby===someone needs to look at the power supply inside the unit to check voltages etc.

Dec 13, 2012 | Combination Televisions

1 Answer

We just purchased a vieja TC-P50GT30 and we can not get the audio to work. Please help

Good day!!!!

Please try to play a DVD or any movies to your TV to determine weather the problem is on the TV itself or on the signal reception or on the digital cable box..

If the TV have audio when you play a DVD your TV is good..

Possible problems are:
1. loose wiring on antenna (coaxial)
2. digital cable fault contact your provider for immediate remedy
3. bad tuner.

Hope it helps..

Dec 02, 2011 | Panasonic Combination Televisions

2 Answers

14 inch monitor starts to show horizontal lines

This is most likely due to pixel degradation. There is no easy way to fix this problem but some have had success with using a pencil and a towel and lightly massaging the screen through the towel with the tip of the pencil.

May 06, 2011 | Panasonic TC-22LR30 22 in. TV/DVD Combo

1 Answer

How to unlock child lock for Panasonic Television model TC-21Z88K?


Just try this method. Most of the Panasonic sets will respond to this procedure.

Panasonic sets need to be reset to clear the v-chip settings. To do this, put it in standby mode, then press the POWER and ACTION buttons at the same time and then turn the power off. The set should reset to the factory defaults, and reset the v-chip.

Mar 02, 2011 | Combination Televisions

2 Answers

Circuit diagram of grundig 5441 tv

Dear Sir,

According to your request i am providing download link
Circuit diagram for Grundig 5441 tv. If you have any problem regarding this issue come back with more information about the problem,we will glad to assist you


in PDF format download High resolution complete Circuit Diagram
Download Circuit Diagram

Thank you for choosing fixya

Good Luck

Aug 21, 2009 | Combination Televisions

1 Answer

Green light blinks.. wont turn on.... standby pwer appears normal.. ihvt and hor output check fine

*This was posted in another thread as a solution to your problem, it would seem that this procedure is for the TV savvy, and I would not recommend that you do this procedure, and that you bring it to a TV repair shop. Or if the TV is still under warranty that you turn it in. But if you are planning on following these instructions I wish you luck, and make sure you follow them to the word so you don't mess up your TV even more.

Found that the thermistor/temp measuring device is suspect, noresistance across legs. There is a label there that says F701 seeservice manual
I went here for a tech manual for the Panasonic
then ordered
Manufacturer: Panasonic
Part Description: FUSE
Part Number: LSJA0411-1
it was mounted to the case that holds the lamp. had to remove the backpanel, etc. Also think I had to splice in the fuse or something. was awhile ago.

i purchased a NTE8115 from my electronics supplier, closest I could find.
Radio shack also has them.

remove the back cover and measure for continuity across the thermal fuse
above the lamp housing.
if open jump it wth a 5 amp fuse, be sure to close the safety switch with
the small blue lever then try to power on.
If comes on ok you will need to replace the entire ballast assembly to get
that fuse.
Panasonic does not have a part number for just the fuse on the PT40LC
It is possible to cut off the fuse and replace with another but dont solder

Jul 15, 2009 | Panasonic Combination Televisions

Not finding what you are looking for?
Panasonic PV-C2010 20 in. TV/VCR Combo Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Combination Televisions Experts

The Knight
The Knight

Level 3 Expert

66352 Answers

Cindy Wells

Level 3 Expert

4718 Answers


Level 3 Expert

6993 Answers

Are you a Panasonic Combination Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides