Question about Altec Lansing VS3251 Speaker

1 Answer

Low sound after headphone unplugged

When i unplugged the headphone, the sound beame too low  even on its maximum volume, i checked the system sound and its set to its maximum and also all the media players sound is set to maximum too,  can somebody help 
your help will be appreciated

Posted by on

1 Answer

Re: low sound after headphone unplugged

Try plugging back the headphones and unplug them agai, but

pull them slowly.

Posted on Mar 23, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

PA speakers distort even at low volume

Firstly check if you R getting clipping at the input ,if U have it, then lower the vol of the music source andif their is no clipping at the source then U must have you speakers checked for it may have some voice coils burnt .with best wishes .system tech.

Apr 13, 2014 | Yamaha S215V Main / Stereo Speaker

1 Answer

Gli sound systems am-1000

test this God bless you
The speakers are not connected properly. Check the speaker connections. The Mute function is activated. Turn off the Mute function. The volume is turned all the way down. Turn up the volume. Neither set of speakers is selected (if unit has A/B buttons to select sets of speakers). Press either A or B to select a set of speakers. Both sets of speakers are selected, but only one set is connected (if unit has A/B buttons to select sets of speakers). Press the appropriate button to deselect the speaker outputs which are not connected. The receiver is set to TAPE MONITOR (if applicable). Turn off TAPE MONITOR mode. Headphones are plugged into the main unit. Unplug the headphones. The source selector is set to the wrong source. Select the proper source. The impedance of the speakers is less than the rating for the system. Use speakers with the correct impedance rating.

Jul 11, 2013 | Speakers & Subwoofers

1 Answer

I have a yamaha "htr-5630"

NEVER USE MAXIMUM VOLUME FOR TROUBLESHOOTING. The errant switch or control that you eventually find and flip will suddenly release the amp's full power and you'll destroy your speakers. If a signal isn't audible at 1/2 volume, for all intents and purposes it's not there.

Look for a misplaced Mute or Tape Monitor control or Multichannel Analog Input selected.

There is a good chance that a common control may have developed a high-resistance or 'dead' spot through idleness and is causing your symptom. Turn the POWER OFF and operate every control throughout its range a number of times, especially rarely-used ones like Tape Monitors and the Mute control.

Turn the volume to something reasonable and see if that helped.

Mar 07, 2011 | Yamaha 5.1-Ch. Surround Sound Home Theater...

1 Answer

Hey, I have a problem with my soundsystem Logytech Z4 and I would like to know if you can help me? The following problem occurs: The black control panel, where I can adjust the volume and bass has a...

Sounds like (no pun intended) the amplifier circuit in the speaker is bad. When you use the headphone the amplifier is not used - only the preamp. It will need repair.

Nov 25, 2010 | Logitech Z4 Speakers

1 Answer

I hooked up the speakers to the back of the PC with the matching green plug in. The speakers are on and working but no sound is coming out. I also clicked on the speaker icon and turned the volume all the...

The first thing to do is to determine if it is the speakers or the computer that is having issues. Plug the speakers into an MP3 play, disk player or some other audio device that has a headphone jack and verify they work. If they do, then you need to determine why the computer is not sending sound to the jack. When you right click on the speaker icon, and select "Open volume mixer" there should be multiple sliders to turn up. Make sure the internal speaker/headphone jack volume is up (and mute not selected) as well as the "applications / windows sounds" volume. comment back to me if you require further assistance and if so, include the model computer and operating system in your comments. Good-luck - Subdriver

Feb 15, 2010 | Logitech X-140 Speaker

1 Answer

When turned on: srm450 has no sound, but all leds (power and signal) is normal. If I turn the volume up (near maximum) , the srm450 sound is activatet again , and peforms normally. I then turn volume down...

2 Unscrew the fixing screws on the back. (just the outside ones)
3 Take the back off and turn the amplifier circuit board to face you.
4 About 2" from the left and about 4" from the bottom you will see a sort of tab. pull it off gently and widen the 2 prongs slightly.
5 Put the jumper tab back on and re fit the amp.

Dec 26, 2009 | Mackie SRM-450 System

1 Answer

Logitech Z4 speakers not working at all. Checked all connections, computer registering them?... but when I plugged my mobile phone earphones in front jack there's still no sound?!

Please click on the Volume icon in the system tray and make sure that the speakers or other volumes are not muted. Windows has a habit of muting things on its own. And unless there is sound going to the speakers the headphone jack on the front of speakers will not function.

Dec 03, 2009 | Logitech Z4 Speakers

1 Answer

No sound from creative t3030 2.1 speakers

the circuit board and amplifacation supply inside the sub are blow or shorted out.thus preventing any sound. the head phone jack works only because it is a bypass feature supported by the actual computer not the surround sound unit

Jul 23, 2009 | GE Ultrasonic 2.1 Subwoofer Computer...

1 Answer

Blippy Sound

Sounds like the cords that are going into the PC/system have static. Remove the cords from the speakers and simply put your finger around the jacks to remove static. Push the cords and the jacks back in and switch on the speakers. Then twist the volume control, turning it up loud and then low, then loud and low again. That should cure the problem as it removes static that gets built up over time. Either that or your speakers could well be damaged.

Mar 28, 2009 | Altec Lansing VS4121 Speaker

1 Answer

Computer stopped recognizing the speakers

You need to reinstall the latest drivers for your present sound device then restart your pc then check it. It will work surely! you should install the drivers that came with your sound devices! thats it!

Dec 07, 2007 | Polk Audio M3 Speaker

Not finding what you are looking for?
Altec Lansing VS3251 Speaker Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Altec Lansing Speakers & Subwoofers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 2 Expert

224 Answers

Ryan S
Ryan S

Level 2 Expert

328 Answers

Are you an Altec Lansing Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides