Question about Malber WD1000 Front Load Washer/Dryer

2 Answers

Malber WD1000 corrugated drain hose stay brackets (both) don't stay clipped to the machine.... since the plastic stays are broken, is there any chance of obtaining those two parts?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Door handle broke at plastic insert. Looking for replacement parts.

Posted on Aug 01, 2009

  • ghousman Sep 26, 2010

    have the same problem. Where did you get help?

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

The plastic handle on my malber WD1000 also broke -- anyone know where to buy a replacement?

Posted on Oct 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have the Malber WD1000,the wash cycle goes on but no water pumps out, a couple drops come out . How do i fix it?


No water fill
1.water valves closed----turn on valves
2. Hoses kinked---unkink hoses
3. Screen in fill hose clogged----clean out screen
4. No power to fill solenoid---replace solenoid
5. Faulty water level control---replace control
6. Machine did not turn on----check control & power outlet
???
Water will not drain from machine
1.kinked or clogged hose----clean drain hose
2.pump does not run----readjust & tighten pump-drive mechanism
3.suds lock----remove suds,, add cold water
4.faulty transfer valve---replace
5.defective timer----replace
6.loose belt---adjust belt

Sep 22, 2011 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Malber 1000 started leaking from the bottom. Water is coming from underneath the machine in the area behind the filter area


Usually what I have found is a small hole in the drain hose or coin trap, sometimes mice chew them and sometimes It is an abrasion wear from the balance brick rubbing. pretty easy fix though.

May 06, 2011 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Hi, How do I open the door on a Malber wd1000 when is it stuck after the cycle is over?


Some machines require it to be empty of water to allow the door to open.Try dropping the drain hose low into a bucket to allow it to open, then clean the filter as it may be blocked causing this problem... Good luck

Feb 10, 2011 | Malber WD1000 Front Load Washer/Dryer

2 Answers

My Malber WD1000 over floas and does not dry = can you advise me


First off, I have found that my machine gets clothes 90% dry (or 75%). Also, when I first installed mine, I did not properly drain it. The drain hose you notice comes out the bottom of the machine, goes up to the top and then goes back down again. I had to take the hose from there back up again to create a trap that held the water so it did not flow back into the machine. (I figured this out by disconnecting the hose entirely and letting the water run onto the ground.
Hope this helps.

Feb 11, 2010 | Malber WD1000 Front Load Washer/Dryer

1 Answer

I lost manual . there are a lot water inside. how


To get the water out , bring the machine forward

Take the drain hose out of the waste pipe

Remove any clips holding it to the back of the washer

Lower the hose into a bucket and the water will drain out under gravity

As for the knob it is a replaceable part but you will need to contact Malber

Nov 13, 2009 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Water in drum after turning off


could be a leaking fill valve ..not shutting off good after shutoff

Dec 08, 2008 | Malber WD1000 Front Load Washer/Dryer

1 Answer

I have a Malber WD 1000 and need to replace leaking drain hose.


The malberusa website has a phone number for New York. Try there. I think the office is in Garden City, LI
Good luck.

Nov 17, 2008 | Malber WD1000 Front Load Washer/Dryer

1 Answer

How long can drain run be


no the pump cant handle the extra length in the hose

Aug 25, 2008 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Drum does not spin


I had similar problem recently. It turned out the main controller right above the drain hose exit on the back was the problem. I got a new board from MALBER and replaced it myself. It is working now.

May 25, 2008 | Malber WD1000 Front Load Washer/Dryer

2 Answers

MALBER WD 800


Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.

Rate me pl.....if helped. Click on 'thanks for trying' if not helped, your prob will be back for someone else to solve.

Feb 03, 2008 | Malber WD1000 Front Load Washer/Dryer

Not finding what you are looking for?

Open Questions:

See all Malber WD1000 Front Load Washer/Dryer Questions

Malber WD1000 Front Load Washer/Dryer Logo

Related Topics:

726 people viewed this question

Ask a Question

Usually answered in minutes!

Top Malber Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Jason Harris
Jason Harris

Level 2 Expert

274 Answers

Are you a Malber Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...