507 error code what does this indicate?

It is helpful to have the sequence of the blinking red light. This may help:

MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927

Page 43

3. Error Code Operational Check

Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational

Check. When the TV is switched Off, the code automatically resets to "12" No Error.



Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,

activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem

has occured since the last Initalization.



Note: The front panel buttons must be used, NOT those on the Remote Control.



• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.



Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.



4. Error Codes

The Error Code designations indicating malfunction, or no malfunction, are listed below:

POWER

LED

STATUS

LED

LAMP

LED

Power

Status Condition

Off Yellow Off Low

Power Excess heat. Check Lamp Filter

Off or On Off Yellow No

change

120w usage time over 7000 Hrs.

150W usage time over 3500 Hrs.

Off Off Blinks

Yellow

Low

Power Lamp Cover open

Off Blinks

Yellow Off " Filter Cover Open

Off Off Red Stby Lamp did not turn On

Off Blinks

Red Off Low

Power Fan Stopped

Off Red Off " Circuit failure (short or DVI

connector unplugged)

Abnormal LED Indications

Error Codes "DEVICE" & "MENU"



Error Codes Description



12 No error detected

22 Recovery from Reset

32 Lamp cover is Open

34 Lamp abnormality

35 DM Fan failed (Chassis Fan)

36 Exhaust or Lamp Ballast Fan failed

37 DMD Engine Fan failed

38 Lamp temperature abnormally high. Remove Lamp to check filter.

39 DMD temperature abnormally high

41 Short is detected (Standby Power Supplies)

42 Lamp Fan failed

44 DVI cable between Format and Engine disconnected

46 DMD Temp. Sensor not detected (check DT connector))

47 DM Temperature too high

48 Engine power supply short detected

51 Speaker Drive circuit short detected

52 HDD excess temperature (V30+ & V31 only)

55 HDD Fan Stopped (V30+ & V31 onlyt)

1. Turn OFF cam
2. Remove the battery or the power supply
3. Turn the switch to CAMERA for about 30 sec
4. Turn the switch to OFF
5. Install the battery or power supply
6. Turn the switch to MEMORY
7. Open the LCD cover and press the RESET button ( small inner button )
8. You will be prompt to adjust date/time. Do it
9. Take some pictures

A blinking yellow for this model indicates the TV is too hot, unplug & allow 30-45 min to cool before re-plugging .
OR: lamp not installed or lamp door not closed. there is a lamp door switch that may not be closing, simulating door not closed

LED Indications

The front panel Status LED provides an indication of

the set's operation and the possible cause of a malfunction.

If an abnormal condition is indicated, perform the

Self Diagnostics procedure.

Self Diagnostics

To activate, press the front panel <ACTIVITY> &<CH

??> buttons at the same time and hold for 5 seconds.

The STATUS LED will then flash denoting a two digit

code.

• The number of flashes indicates the value of the

MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2

second.

• The LED then flashes indicating the value of the

(ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.

Example: If the Error Code is "23", the LED

will flash two times, pause, and then flash three

times.

Table 2-2: LED Indications

Error Codes, descriiptions and the most likely cause of

the error are listed in Table 2-3.

Note: The TV must be in "Shut Down." The LED

will probably be indicating an abnormal

condition. If the TV is switched Off, AC is

removed, or a System Reset is performed, the

code automatically resets to "12" No Error.

See the Error Code Log to retrieve a history of

errors.

Note: Use the front panel buttons, not the remote

control.

Note: If there is no response, the front panel may be

locked by a V-Chip setting. To unlock, press

and hold <ACTIVITY> on the front panel for

8 seconds.

LED Indication Condition

Off Off (standby)

Green Power On

Slow Blink Green Power Off with Timer Set

Fast Blink Green (80 seconds) > Off Power Off (Cooling fan still working, 80 sec)

LED Indication Condition

Red Lamp Failure

Yellow TV Too Hot

Slow Blink Red TV May Require Service

Slow Blink Yellow Lamp Door Open or No Lamp Installed

NORMAL INDICATIONS
ABNORMAL INDICATIONS (For details perform Self Diagnostics Procedure.)

do the following steps: God bless you
To start test program, press and hold both POWER SCRUB PLUS and RINSE & HOLD program buttons, then turn unit on by pressing ON/OFF button. When program buttons are released, lights above them will flash. To end test program, press ON/OFF button.To check program indicator lights (POWER SCRUB PLUS, REGULAR WASH and RINSE & HOLD), press and hold each program button. When REGULAR WASH program button is pressed, CLEAN light also comes on.
To start testing, press both POWER SCRUB PLUS and RINSE & HOLD buttons a second time. When testing has ended and a fault was detected, the following indicator lights will be lit:
POWER SCRUB PLUS = Heater fault
REGULAR WASH = Water filling fault (over or under filling)
RINSE & HOLD = NTC (temperature sensor) fault ? note circulation motor stops shortly after it started during an NTC fault
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), REGULAR WASH light will come on and unit will continually fill and drain where testing won't be completed. If flow switch (e5) has failed (opened), water won't heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), RINSE & HOLD light will come on immediately and testing will end shortly after water has started circulating.
If more than one fault occurs, more than one light will be lit.

On the back of the garage door opener there is a red button. Depress this button and sync your keypad to the opener. This will re-establish the code and reset the remote.

Batteries in the UPS typically last 3 to 5 years and it depends upon several factors. including the number of times the unit must go on battery power and environmental conditions. There are usually several batteries in the UPS and while the battery voltage may show 13 volts, this may only be a float charge/voltage and a true indication of the battery voltage and condition requires the batteries to be tested under a load. There maybe one battery in a set of batteries that is faulty and causes the whole battery system to fail and indicate a battery fault.

These lower powered and cheaper type UPS are switch over types, when the mains supply fail, the UPS switches over to the battery and inverter in milli-seconds which then supplies mains power. A faulty inverter circuit and or flat batteries won’t deliver standby power when the mains supply fails.

This indicates an error with the pressure switch and indicates that it is jammed on full. First try switching off ther AC power to the washer and letting it stand for 30 minutes. Then switch back on the AC power and see if the error is still present. If it is then the pressure switch will need to be replaced. The pressure switch is how the machine determines how much water there is in the machine and if the switch is indicating the machine is full it will automatically pump and empty as soon as new water enters the machine.

Press the OK button.
- If paper is being fed at error occurrence, the
error is indicated after the paper is ejected.
- If the error occurs, the print head alignment
values are not changed.
- After exit from the error by the OK button,
the automatic print head alignment will not
be re-done.
The error will occur when the print head
alignment pattern is not printed due to no ink
or non-ejection of ink.

HI.The Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door)

1. If door latched:

1. Disconnect power from unit.
2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
3. Replace door switch.
4. Re-apply power.
5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.

2. If door not latched:

1. Disconnect power from unit.
2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.

the status light blinking red means a fan (the unit hs 4 of them) has failed. you need to determine which one. use the self diagnostic function:
Error Code Operational Check
Note: The TV must be in “Shut Down” and not manually switched Off, to perform the Error Code Operational
Check. When the TV is switched Off, the code automatically resets to “12” No Error.
Press the front panel “DEVICE” and “MENU” buttons at the same time, and hold for 5 seconds to
activate the Error Code Operational Check. The LED will then flash denoting a two digit Code.
Note: The front panel buttons must be used, NOT those on the Remote Control.
• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.
• The flashing then pauses for approximately 1/2 second.
• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.
Example: If the Error Code is “32”, the LED will flash three times, pause, and then flash two times.
• The Error Code is repeated a total of 5 times.


and read the code.
35= Chassis Fan failure
36 =Exhaust (Back Cover) or Lamp Ballast Fan failure
37= Engine (DMD or Lamp) Fan failure