E 91:01 and flash symbol is flashing - Sony Cyber-shot DSC-W80 Digital Camera

Usually when the symbol is flashing you have to replace the rinse agent. So look for the place where you can pour it in and the flashing symbol should be gone. As for the flooded floor you may need to contact a repairman

By unit, do you mean the thermostat? And if so, do you mean the whole face is flashing, or just a heat or cool symbol? And if your talking about the heating/cooling unit, are you talking about a flash on the board?
A thermostat face that is flashing is usually batteries.
A symbol that is flashing on a thermostat indicates a call and is in a delay. There will be a 5 minute delay on calls if the call has been short cycled, powered off and on, etc.
If the symbol continues to flash for an extended amount of time, then the problem is in the furnace, air handler, etc.
If the system is working, but flashing, then it could be the programming of the thermostat.

There is a method to do it. But not simple. But following few steps you can do it.

Visit SmartUSB.net.

It explains step by step, how to insert symbols to flash drive label.

http://www.smartusb.net/p/insert-symbols-to-flash-drive-label.html

I think you will also like these things,

Change your flash drive icon

http://www.smartusb.net/p/change-flash-drive-icon.html

Hide a file or folder in your flash drive

http://www.smartusb.net/p/hide-file-or-folder-in-flash-drive.html

Add wallpaper to your flash drive background

http://www.smartusb.net/p/add-wallpaper-to-flash-drive-background.html

Change font color in your flash drive

http://www.smartusb.net/p/change-font-color-of-your-flash-drive.html

If Polaroid x800 flash doesn't turn ON - that is because of the picture mode (a plastic switch on one of the sides). In my case: mountains symbol - flash turns ON/OFF, flower symbol - flash is stuck to OFF.

First, check to make sure you're not in the macro mode. There's a slide switch on the end of the camera, near the SD card slot. Slide the switch away from the flower toward the mountain to take it out of macro mode. The flash won't fire in macro mode.

Then, if the flash still doesn't fire, take a look at the flash mode. Press the up-arrow button to bring up the flash menu. If it's currently set in the lightning-bolt-in-a-circle-with-a-slash-through-it symbol, you've got the flash turned off. Set it to the lightning-bolt-and-"A" for automatic flash or the lightning-bolt for forced flash.

If the flash still doesn't fire, then it's broken.

You can re-enalbe the flash of this camera by pressing on the lightning button repeatedly until flash is enabled

Hi,

To get rid of this flashing message symbol please delete the sim messgaes.

To delete the sim messgaes follow the steps,

Menu--->Messages--->Options---->Sim messgaes
open it and you can delete the sim messages.

You wont get the flashing message symbol

Thanx

The flash mode button is located to the right of the zoom button. Press the button several times to cycle thru flash modes.
Suppressed flash is the round symbol, where the lightning symbol is crossed over.

In your display, is the small lightning symbol appear on the screen? Try cycling through the various flash options by pressing the "flash" lightning symbol to the right of the monitor. If the flash is set to flash when there's not enough light at the G9's descretion (with an "A" next to the symbol) then the flash may or may not go off. I oftentimes set the flash to go off all the time if the camera is not doing it automatically (with the A next to the symbol). Being in Auto mode versus the other preset exposure modes affect the flash options available too.

Shaving head check indication After two years of use the red shaving unit symbol î will flash for 30 seconds during 7 shaves to indicate that you should check the condition of the shaving heads. This indication is based on an average shaving time of 3 minutes per shave. When the shaving head symbol flashes, all other symbols and lights are out. When the shaver is switched off, the shaving unit symbol disappears. When the red shaving unit symbol starts flashing, you should check the shaving heads for possible damage. If the shaving heads are damaged in any way, they must be replaced in order to obtain optimal shaving results