Question about Brother DCP 130C All-In-One InkJet Printer

1 Answer

Printer problem i put a new catridge ink but it doesn't accepted by the printer.always says replace ink, even though it is already inserted a new one.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 832 Answers

Try to unplug the printer from power. Wait a minute. Take all carts out. Close ink cover. Replug printer to power. Machine demands carts. Insert carts as demanded.

If you still have this error this could be due to generic ink carts. Ink may have stained the led control and the ink assy has to be replaced!

Posted on Nov 10, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I insert the ink cartridge

power on the printer, open the catridge door. after printer initializes the catridge carriage assembly comes to right side of the printer and settles then insert the catridges and close the door.

Oct 17, 2014 | HP Office Equipment & Supplies

1 Answer

Ip2770 black ink doesn't apperar on paper although there is no nitification of cartidge damage

you most proberbly have a clogged black catridge. try cleaning from the printer's maintenace tab. if it doesnt improve after a few cleans, do a deep clean. if it still doesnt work and you dnt feel like buying a new catridge yet, steam the nozzle of the catridge. these steps almost always do it, if not, just get a new catridge and voila!

Jan 19, 2013 | Canon Pixma iP2700 InkJet Photo Printer

2 Answers

Hi my samsung ml-1610 mono laser printer shows red light contineously i dont know what the problem is can u help me please

see, you have inserted the paper well. if not solved, your catridge have low ink or empty. so bring a new catridge or if you can, refill the catridge. 1610 catridge can be easily refilled.

Aug 27, 2011 | Samsung ML 1610 Laser Printer

1 Answer

Tells me ink needs replaced even after putting in new ink.

check your new ink catridge and look for a mini green electronic chip if that is damaged the printer shouldn`t recognize the catridge

May 16, 2010 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer


you get from dell 922 all in one software 'replace catridge' option use that option

Feb 24, 2009 | Dell 922 All-In-One InkJet Printer

1 Answer

My Dell printer has worked fine for years, for some reason the color started fading even though the levels were over 50%. Finally the black ran out so I went and had it filled like I always do. When I...

In this case what i would request u to do is.......
Take out both the catridges from the Printer.........
Take 2 Paper Towels one should be wet with Luke warm water and the other one should be dry...........
Take the Colour catridge first turn it upside down and u will see a small copper plate on the catridge from where the ink comes out.......
Place the wet paper towel using ur thumb on the Copper plate and press it a lit bit for 10 Seconds......
Now remove it and see whether u see any ink on the paper towel..........
U should see some ink on it now place the dry paper towel on the ink catridge in the same way........
Now do the same procedure again..........
Do the same procedure twice on the Black Catridge.................
Now take the dry paper towel and turn the direction of the cartridge so that u can see a Copper plate on it with small boxes just clean that copper plate with the Dry Paper Towel..........
Know insert both the catridges inside the Printer...........
Good Luck

Jan 27, 2009 | Office Equipment & Supplies

1 Answer


whats your printer model?clean the catridge contacts and the print head insert it again properly then switch off and on,do a hard reset from the menu button ,and make sure your using a genuine catridge most especially if your printer is hp product.that should work

Aug 23, 2008 | HP OfficeJet 6310 All-in-One Printer...

1 Answer

Printer problems

Unfortunately, both slots have to have the correct cartridge inserted in order to print. You'll need to get the color cartridge, too. Even though you think that you're only using the black one it actually pulls from both. Sorry.

May 19, 2008 | Dell A940 All-In-One InkJet Printer

Not finding what you are looking for?
Brother DCP 130C All-In-One InkJet Printer Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

James Cagle
James Cagle

Level 2 Expert

478 Answers


Level 3 Expert

379 Answers

Jim Keysor

Level 2 Expert

329 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides