I have gone to feature **244366 and password 23646, and terminals and sets, and the extension number - but then i dont get any prompt that says Line Access or configuration or wahtever you guys were talking about ...how do i get this prompt in order to continue.......
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Try pressing the FEATURE button then, **266344. On some Norstar phone systems there is also an Admin level of programming that is useful if you only need to change the names or the time. To access Admin programming, press Feature**23646(spells admin on the dial pad). Then 23646 for password.
Press "Feature * * 266344"
At the password prompt, press "23646"
This should bring you to the Terminals and Sets menu and you can enter the extension number and change the Set Name.
To solve this problem you have to go into programming . Press feature ** 266344 then put in the passwored which is 23646 this gets you to terminals and sets put in your set number and step through for volume.
Well that is better than most people in finding the arrows...
Ok, first you need to know the extensions that you want to program to ring, and the lines, record these numbers... if you do not know the extension numbers and actual line numbers; going to each set, and doing a FEATURE * 0 and the Intercom and line buttons this will tell you the extension number and line number (this also tells you what is on every button).
Then goto your set and put in: -> FEATURE 2 6 6 3 4 4 -> Password: 2 6 6 3 4 4 Now you will have to look at your LCD for 3 arrows <- Heading....Enter-> <- Back .......Next-> You will not see these words in the LCD display, you just have to look for the arrows that correspond. -> you will now see “TERMINALS&SETS” and press Enter (the top right arrow key) -> now put in the extn that you want to change (Eg. 227). -> you should now see the extension number“227: NAME” ->press Enter (the top right arrow key) again -> you will now see “LINE ACCESS” -> press ENTER -> you will now see “LINE ASSIGNMENT” -> and Enter -> now you can type in the lines that you want to ring on this extension (Eg. 025 for line 5) -> hit CHANGE till it says "APPR&RING" (Appear and ring means that the line will have a button on the set) -> hit NEXT to save changes -> press FIND to look for more lines and change the appropriate lines to appear and ring -> then the RLS button (the little orange button) to exit programming.
After this programming is done, dial Feature * 0 and look for these new lines.
To change # of rings you have to go into programing OK press feature * * on the main set and config (266344) then the password admin (23646) this goes to terminals and sets hit show and enter the set you want to change go to capabilities this will allow you to chang # of rings on that set
1. Press the Rls button then ** FEATURE 266344 (CONFIG)
2. Password is 23646 (ADMIN) The display reads Terminals & Sets
3. Press SHOW ans enter the Extension for which you want to enter a name.
4. Press SHOW, again
5. Press the NEXT key until the display reads NAMES at the top left corner.
6. The bottom right corner reads CHANGE, press the far right soft key.
7. To move from one letter to the next use the far right and far left soft keys or the # key.
8. When you are finished Press next.
9. Press the HEADING key to get back to TERMINALS & SETS and start again!
Navigation Keys: Line 1 = HEADING Speed Dial = SHOW
Line 2 = BACK Last No. = NEXT
This can only be done from the main handset and only one at a time. The Soft Keys are the three small buttons right bellow the screen.