Question about Pentair 250k Minimax Ch Ng Mv Heater

1 Answer

The burners and pilot turn off after start up

The burners and pilot turn off shortly after start up and won't stay on.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 246 Answers

Assembly valve replace

Posted on Sep 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fireplace burner won't stay on


try cleaning the pilot sounds like its a short pilot and when the burner comes on it pulls the gas from the pilot light .

Feb 22, 2013 | Heating & Cooling

1 Answer

Pilot won't stay on


Burners don't have anything to do with the problem of pilot not lighting. Is the problem that flame will not 'stay' lit? Or you can't even get a flame to ignite? If former: possible bad pilot generator or bad gas valve. If latter, possible bad gas valve or no fuel to ignite.

Dec 23, 2012 | Hayward H Series Pool & Spa Heater 400k...

1 Answer

I changed the thermo coupler and the pilot light does stay lit but the burners won't light


If you are referring to a gas fireplace:

  • Make sure the pilot knob is turned from "pilot" to "ON" or it will never run.
  • If the pilot knob is "ON", and the pilot is lit, but the burner won't light, it could be a bad Thermopile. The thermopile is the other safety mechanism in the pilot assembly that controls the burner.

Dec 19, 2012 | Heating & Cooling

1 Answer

Pilot light won't stay on


What is the model number of the unit?

Nov 27, 2012 | Tappan Kitchen Ranges

1 Answer

Burner won't light, pilot is burning just fine.


Once you get the pilot to light and stay lit did yall move the burner knob to the ON position? Is the temp knob all the way up?

Nov 27, 2011 | Procom Heating & Cooling

1 Answer

The pilot won't stay lit on gas hot water tank.


Make sure thermocouple tip is seated inside the burner flame.
Make sure thermocouple is not overtightened. Finger-tight + 1/4 turn.
If the pilot lights, then ECO energy cut off is not tripped, but gas control valve might be bad.
Check color of pilot flame: it should be strong and clear blue.
If pilot flame is weak, or color of flame is yellow-orange: Clean pilot orifice and burner and combustion parts on yearly basis.
Clean air intake screen if applicable.
Increase air supply to water heater. Open a window and see what happens.
Check for adequate draft going up chimney using match under vent hood to see if smoke drafts immediately upwards.
Bleed air out of gas line.
Check gas pressure.

Open following links for troubleshoot resources:
http://waterheatertimer.org/pdf/Pilot-light-will-not-stay-lit.pdf
http://waterheatertimer.org/pdf/Pilot-outage-troubleshooting.pdf
http://waterheatertimer.org/pdf/Vent-spillage-test-atmospheric-gas-water-heater.pdf
http://waterheatertimer.org/How-to-install-gas-water-heater.html#troubleshoot

Sep 21, 2011 | Water Heaters

1 Answer

Iv"e purchased a older home with an old 1984 era furnace. The pilot light will activate the burners but the burners won"t stay lit.


Make sure the thermostat is turned all they way up.
Also make sure the gas valve is turbed to on instead of standby,

Jul 03, 2010 | Heating & Cooling

1 Answer

William forshaire 435 runs well for awhile until


Try cleaning your thermocouple,and resetting it where was, which is located at the pilot flame. this should solve your problem.

Feb 23, 2010 | Heating & Cooling

2 Answers

I have a 3 burner pitco gas friolator and dont know how to light the pilot any suggestions


First, never light when the pot is empty, you can fill with water if you have no oil. Open the door, check the thermostat and make sure it is turned off.(The burners will light if thermostat is on) Behind the thermostat you will see the gas valve. Turn knob to off, then to pilot. There is a notch at the pilot position. Now look up in the middle behind the burners and you will see the pilot assembly. Push in on the knob on the gas valve while you hold a long lighter close to the pilot assembly. Once the pilot lights keep holding the pilot knob in for 20 seconds. Now let off the pilot knob. Pilot should stay burning. Now turn the gas valve from pilot to on. Now turn the thermostat to desired temp and the burners will fire off and start heating.

Oct 15, 2009 | Kitchen Appliances - Others

Not finding what you are looking for?
Pentair 250k Minimax Ch Ng Mv Heater Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pentair Pool & Spa Experts

Pj Kiley
Pj Kiley

Level 1 Expert

21 Answers

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Bill Jordan

Level 2 Expert

372 Answers

Are you a Pentair Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...