Question about Pitco Frialator SG14 Deep Fryer

1 Answer

Igniter not sparking? - Pitco Frialator SG14 Deep Fryer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 81 Answers

The cheapest part to start with is the ignitor itself, if that is not the culprit then it will be your ignition module located behind the front panel.

Posted on Jul 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Single wire igniter that sparks the oven on but flame goes out after a few seconds. Does the igniter control gas valve?


Its the other way around the valve controls the igniter so to speak

GAS OVENS 1)The spark igniter tip is dirty (can clean it with either a little wire brush or a piece of fine sandpaper).

2) The Pilot flame is too low, and the tip of the igniter is not in the flame good enough. (the flame acts as a circuit when it touches the tip & completes the circuit).

3) The spark module is no good and needs to be replaced.(But 1 & 2 are your best bet).
spark module does not sense the flame when it's on. The spark igniter is also the flame sensor which provides feedback to the spark module.

Make sure the igniter is properly aligned with the burner lighting holes and it is clean. All lighting holes must be clean too. You can enlarge them using a drill bit one size bigger.

If it would not fix the problem, replace the bake burner and the igniter.

There is a small chance for the spark module itself to be bad as well.
ELECTRIC OVENS:

CHECK THE OVEN RELAY CONTROL BOARD Aclicking sound could be something wrong with a relay. Check for any loose connections around the main control board on your oven. The click you hear is a relay losing power and switching back on. If the clock resets then something is causing power interruptions to the board.

Mar 23, 2015 | Ovens

1 Answer

Why won't my weber q grill light


Check to see that wire from igniter switch is connected to the igniter itself. If it is check to see that there's a spark from the night. If there is a spark but still low flame ignition try adjusting the igniter so the spark is closer to the burner. Most likely, the igniter is no longer any good.

Jul 27, 2014 | Weber Grilling

2 Answers

Kenmore gas range when no clicking when turning the oven on


Get FREE Standard Shipping on orders of $100 or more. Details
Range: Gas burner won't spark or ignite A surface burner igniter switch and a spark module activate the spark electrode when a burner is turned to the "Lite" position on a gas range's cooktop. If the surface burner switch, spark module or wiring in that circuit fails, the spark electrode won't work, and as a result the gas burner won't light. If those components work but the electrode won't spark, the problem could be that the spark electrode is coated with spilled food of is bent or broken. In addition, the electrode won't spark or ignite the burner properly if the ceramic insulation sleeve below the tip of the electrode is cracked or broken. If the gas burner isn't lighting, these repairs may help.
Range 101
See all articles These repairs may help solve your problem:

Replace the spark igniter electrode

1396454293470.jpg The spark igniter electrode-also called the surface burner igniter-is an insulated electrode that provides an ignition spark to light a surface gas burner. It sparks and makes a ticking sound when the burner switch is turned to the Lite position. Replace the spark ignition electrode if it fails to spark or if the ceramic insulation sleeve is cracked or chipped. How to Replace a Spark Igniter Electrode in a Gas Range Find This Part

Replace the surface spark module

1377098014986.jpg The surface spark module is in the ignition circuit for the gas surface burners. When a surface burner control knob is turned to the "Lite" position, it provides voltage to the spark electrodes on the gas surface burners. If the surface spark module fails to provide the electrodes with voltage, then it should be replaced. Find This Part

Replace the spark igniter switch

1396454315355.jpg The igniter switch is an electrical switch on the stem of the gas surface burner control valve. This switch completes a circuit to the surface burner spark module, causing the burner igniters to spark when the burner switch is turned to the Lite position. Replace the burner igniter switch if the burners don't spark when you turn the burner control knob to the Lite position or if igniters spark constantly even when the burner knobs are in the Off position.

May 27, 2014 | Kenmore 79012 / 79014 / 79019 Gas Kitchen...

1 Answer

Igniter works gas kicks on after igniter stops if it would spark a little longer it would lite I can lite it with a match


Check igniter! You don't have the right spark? Lots of times it will short out & you can see the sparking elsewhere other than just at the gap at top of the igniter. The other thing to check is ensure that the orifice is completely clean at the pilot burner. A clean pilot orifice and the proper spark will ignite the heater.

May 19, 2014 | Pentair MiniMax 100 Natural Gas Swimming...

1 Answer

The striker button won't light the grill but a match will. It is an older Genesis Silver approximately five years old.


Hello,
If your piezzo ignitor is still sparking, but not lighting the burners, then you may have one of the following problems. 1) If you have a standard push button piezzo igniter or a rotary style igniter, check for spark. Can you hear or see the spark? It's hard to see the spark in bright daylight. It's easier to view the spark at dusk or dawn. It should spark an "arc" at the burner. If not, adjust it if necessary. 2) The igniter wire may have a short, causing the spark to arc somewhere else along the wire and not at the burner. Replace igniter wire. 3) It's also possible the igniter tip where it sparks has a cracked or broken porcelain portion of the igniter, causing the spark to not arc at the tip where it's supposed to. Replace the igniter piece. 4) Your burner may be clogged or rusted at the point where the ignitor sparks to light it. Clean the burner. 5) If your push button ignitor is not sparking at all, it may be stuck inside from being out in the weather. While pushing it, spray it with WD-40 to unstick it.
Hope this helps. Douglas

Aug 05, 2010 | Weber Genesis Silver C Grill

1 Answer

Need to manually light the grill as the starter is not working


Hello,
Is the igniter sparking? Some are battery powered-check the battery or replace it. If you have a standard push button piezzo igniter or a rotary style2_bing.gif igniter, check for spark. Can you hear or see the spark? It's hard to see the spark in bright daylight. It's easier to view the spark at dusk or dawn. It should spark an "arc" at the burner. If not, adjust it if necessary. The igniter wire may have a short, causing the spark to arc somewhere else along the wire and not at the burner. Replace igniter wire. It's also possible the igniter tip where it sparks has a cracked or broken porcelain portion of the igniter, causing the spark to not arc at the tip where it's supposed to. Replace the igniter piece.

Hope this helps! Douglas

Jun 03, 2010 | Fire Magic 11-S1S1N-A Stainless Steel Gas...

1 Answer

Igniter Stopped working


Igniter could be shot. Take out igniter and put near something metal. Push button to see if sparks occur. If not igniter is no good. If this works, the end of wire that is near wear the igniter sparks to light grill could be to far away from metal, bend to get closer to metal, so it will spark, or end could be covered with grease, clean end and try for spark again.

Jun 14, 2009 | Weber Performer Grill

1 Answer

We have a rheem furnace we replaced the igniter but still getting no spark what else could them problem be the fan works but getting no spark or heat why


Is it a true spark igniter or is it a hot surface igniter? You need to use a volt meter and call for heat. Check to see if you have voltage going to the igniter. If its a spark igniter and you are not getting a reading then it is the module that is the problem. If it is hot surface, then its the control board.

Apr 01, 2009 | Heating & Cooling

1 Answer

No spark to igniter


The ignitor does not spark- it glows.

Dec 22, 2008 | Reddy Heating & Cooling

1 Answer

Spark Igniter not working


Find the spark igniter control box usually on the back inside a metal can take out of the can and check to see it spark is jumping between wires to the individual burners if not and just one burner is not lighting you probably have a cracked spark discharge point.. look at the offending burner and see if it is dirty or pushed down in or the porcelain is cracked. replace if cracked..

If spark module is jumping spark you need to make sure wires are insulated from each other and exchange places with the offending burner igniter to one that works to see where the problem exists. ...be careful to not get zapped while playing with the module!!!

Apr 19, 2008 | GE Profile JGSP44 Dual Fuel (Electric and...

Not finding what you are looking for?
Pitco Frialator SG14 Deep Fryer Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pitco Frialator Kitchen Appliances - Others Experts

Angel Joseph Jr.
Angel Joseph Jr.

Level 2 Expert

684 Answers

Paul Carew

Level 3 Expert

3239 Answers

Treefrog15
Treefrog15

Level 2 Expert

127 Answers

Are you a Pitco Frialator Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...