Question about Lite On Laars Lite 2 Heaters: 250,000BTU MV Heater

1 Answer

I've had this unit for about four yrs. It has worked fine, however today I cann't get it to turn on to heat the pool. Can you assist?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 53 Answers

How often is this unit serviced??? Every 12 months is the normal recommended period.
May just need cleaning.

Posted on Jul 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My polaris booster pump just gets hot and wont run


the motor is bad overheating need a new booster pump

Sep 08, 2014 | Polaris Pb460 Polaris Booster Pump...

1 Answer

Pool pump turns off after 1/2 hour or so but I can turn on manually after it sits for a while. Timer is working fine. Hayward Super II around 5 yrs old. Do I need to replace this motor? This problem just...


Your pump is protected by a thermal device that shuts it off when over heated. Are you running 110 or 220? In my experience, your pump will run cooler on 220 ... consider coverting if appropriate.

Aug 28, 2010 | AO Smith Pool Pump Motor Hayward Swimming...

1 Answer

10000 gal pump


as with any pool pump they have to prime themselves,, close up the unit as it was before,, and turn it on,, remember that water is also the cooling agent for these pumps, check to see that its pumping water as before,, ( yours may even have a place to prime it,, Look for an easy access prime hole in the pump unit itself )

Aug 02, 2010 | Intex 1000 Gallon Easy Set Swimming Pool...

1 Answer

Rheem digital gas pool heater fan code


The Fan code would indicate a problem with the combustion air blower. The is a pressure switch to indicate there is sufficent combustion air, and if not then unit shuts down. Either the fan isn't running, or there is an obsturction in the fan or exhaust piping, preventing enough air flow.
cfh would be call for heat, which would be a normal display when water temp is below setpoint
See the link below for a manual. Once you open the page look on lower right side for documents, then install manual
http://www.rheem.com/product.aspx?id=2388EEB7-3DEC-4601-AE76-EC7A07F17630

Jul 04, 2010 | Solar Rheem Gas Fired Pool & Spa Heater...

1 Answer

Heater not coming on


if voltage to unit then check transformer if voltage see if voltage to gas valve when igniting also check pressure switch

May 22, 2010 | Raypak Versa 130,000 Btu Above Ground...

2 Answers

Rheem model p-m266a-en-c digital gas pool heater runs, shuts down


CFH is call for heat not sure what spk is, but will find out and let you know.

Jul 05, 2009 | Solar Rheem Gas Fired Pool & Spa Heater...

1 Answer

Raypak pool heater piliot light on heat will not turn on


Make sure that gas control knob is set to ON (counterclockwise). Make sure that ON/OFF switch is ON. Check that temperature setting is high enough to call for heat. Make sure pool pump is running and water is flowing to unit.
If not above there is a diagnostic procedure on page 33 of manual at:
http://www.raypak.com/uploads/6000.52AG.pdf

May 24, 2009 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

Millivolt pool heater will not ignite


Most heaters do not require power for the pilot to remain lit. Is there power at he unit? If it worked yesterday and not today has anyone turned it off at the circuit breaker? If you have power turn the gas valve off for 10 minuets and then relight to see if it needed a reset.

May 23, 2009 | Teledyne Laars Laars Lite 2 Pool Heater...

2 Answers

My HP deskjet F380 is showing E


Try this :-
Resetting the All-in-One
  • Press the On (fa37665.gif) button to turn off the unit.
  • Disconnect the power cord from the back of the unit.
  • Connect the power cord to the back of the unit.
  • Press the On (a477fdf.gif) button to turn on the unit.

Jul 15, 2008 | HP DeskJet F380 All-In-One Printer

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lite On Heating & Cooling Experts

paulcarew

Level 3 Expert

2463 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Lite On Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...