Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

Open Question

Loud cluck evey 5 seconds during spin cycle on my whirpool top load washer

Replaced the coupler and still loud clunk and whiring gear noise.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 249 Answers

SOURCE: Loud Noise during spin cycle

drum bearings are gone,it would cost too much to repair,the drum shaft would to be repalced as well.Sorry

Posted on Dec 17, 2007

Ad
Coldcut
  • 1554 Answers

SOURCE: Whirlpool LHW0050PQ Front Loading Washer VERY NOISY during spin cycle

remove the top access panel 3 screws in top rear.
now look around and push on the drum from top
it has suspension shocks and springs like your car they should resist any movements.
look/wiggle the concrete balance blocks , no cracks or loose.
inside the tub are the arm solid /not loose.
run it with the top open what do you see/hear and where
look under the rubber flap in front did anything get under the tub

Posted on Mar 04, 2008

robocop
  • 90 Answers

SOURCE: Whirpool lsq9244eqo fills and drains but does not spin or agitate

It sounds like the agitator gripping teeth are worn out. To check this, take the agitator cap off with a strong knife or flat-head screw driver, pull the cap off and check the plastice teeth and four plastic hooks that grab the teeth. If they are worn out, then you will have to replace the agitator. To replace it, you will see a nut that is between the circlular teeth. Unscrew the nut and pull the agitator up hard.

Posted on Jan 19, 2009

the_admiral6
  • 14 Answers

SOURCE: Washer drum shakes excessively during fast spin

y shaped piece that contains the spindle that attatches to the basket and allows it to spin is corroded and cracking. you can't buy just the spindle bracket, you must buy the basket too. you'll be buying the front part of the drum too, if you wait to long.

Posted on Mar 07, 2009

  • 240 Answers

SOURCE: washer sounds like off balance during spin

old duets have nut on rear pulley that becomes loose. remove rear panel and tighten nut. check while spinning by hand if pop is felt. if it rotates smoothly then you may need new shocks on tub

Posted on Mar 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHIRPOOL WASHER LSQ9564MQ0 Started making loud


judging by the description i would say more likely the coupler
its a three peice part that sits between the mototr and transmission, kinda like a clutch,
anyway it is easily repaired
and available on appliancepartspro.com
type in your model number.....
look for motor coupler

Oct 13, 2009 | Washing Machines

1 Answer

Kichenaid kawe570bal0 agitator clunks


there is a gear, pop the top cap off the agitor, the gear is in there, near the top might need to be replaced, sears has most parts for most machines

Oct 03, 2009 | KitchenAid KAWS850L Top Load Washer

1 Answer

Won't spin, makes clunking noise, drains fine


If it agitates fine , with normal noise , drains with lid closed , then the problem is probably the transmission .

Aug 02, 2009 | Kenmore 24032\24036 Top Load Washer

2 Answers

Washer won't agitate or spin out.


Well it is ethier Belt, Cluch ,motor ,Or transmission. But it does sound like your transmission . The loud clunk is the brake in the gear case ( Trans.). It might have broken off.

Apr 05, 2009 | GE WJSR2070B Top Load Washer

1 Answer

GE Top load washer 15years old. noisy when spinning


washer making a load cluck noise when the spin cycle starts.
It only happens when the motor turns slow for the first minute during the spin cycle. Otherwise it works fine.
if the motor is proper then the bearings in the motor got rusted and that needs replacement.the beasrings are located on the back of the motor.


Apr 03, 2009 | GE WVSR1060A Top Load Washer

1 Answer

I have a Kenmore series 80 washer that is making a loud clunking


check the motor coupler between the gearcase and motor for wear. If it is cracked or broken it will need to be replaced

Jan 04, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washer making noise during the spin cycle


Hi!!! it looks like your motor coupler is failing..Good luck..

Jan 03, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 90 series loud whirring/howling noise during spin cycle


Sounds like you have a broken motor coupler. They are inexpensive. Can be a little tough to replace but I can walk you through it. You can purchase a coupler here.
http://www.shop.washermd.com/product.sc?categoryId=1&productId=1
Dave

Dec 18, 2008 | GE WBSR3140DW Top Load Washer

1 Answer

When replacing direct motor coupler not enough?


Gear case part # 3360629 retails for about $170.
This dosn't happen very often.
You can find a junk whirlpool, roper, kenmore or kitchen-aid and pull the motor and gear case to save $$$$$

Jan 22, 2008 | KitchenAid KAWS850LE Top Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers

Marvin
Marvin

Level 3 Expert

84625 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...