Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

Open Question

Whirlpool Cabrio washer wtw6200vw0 displays error code OL. What does this mean?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
the dr
  • 447 Answers

SOURCE: Whirlpool washer Cabrio WTW6600SB1

Its the Rotor Position Sensor very easy solution!!!chat with me online and ill step you through it save up to $65 (my in-home rate in florida is $75!!!!!!!)

Posted on Sep 27, 2007

Ad
  • 1 Answer

SOURCE: Whirlpool Cabrio Washer Error message code F1

I have started a petition to be sent to the CEO of Whirlpool Corp., Jeff Fettit.
Follow the link, and please sign it! The more the better! Spread the word!
You may also copy and post it to any other groups/discussions about this problem.

http://www.petitiononline.com/cabrio08/petition.html

Thank you!!!

Posted on Aug 02, 2008

  • 3 Answers

SOURCE: keep getting LD error code on whirlpool cabrio washer

Is there water in the bottom of the tub? If yes then open back of washer and remove drain pump (on left side) and pull off of tub and clear whatever is blocking its impeller.
If the water is all gone and drained but pump stays on for several minutes and then gives "LD" fault then open back and check the small clear tube that is attached to the tub. Make sure is not blocked with debris and check tube and tub for anything that could block the small clear tube. If these are ok then remove 3 screws in back of the control panel, pull open control panel and check the clear tub all the way up from the tub to the washer controller board (computer) make sure it is not kinked or disconnected. If not then the problem is most likely the pressure sensor on the (computer). This unit will have to be replaced.
You can test the sensor by doing the following: 1. When the "LD" fault comes on start by pressing the pause button. then pull the clear tube off of the computer board. Then attach a tight fitting drinking straw over the sensor. Press the start button and wait for 60 seconds - If the washer does not start the spin cycle on its own after the 60 seconds then **** on the drinking straw that you attached to the pressure sensor earlier. The sucking action should reset the sensor thus telling the computer that the water is drained and it will start the spin cycle. Just remember if you have to do this to get the washer to spin - that means the sensor is damaged most likely from moisture traveling up the tube over time. The computer board will need to be replaced. I believe it costs $205 without shipping. Hope this helps.

Posted on Apr 05, 2009

  • 180 Answers

SOURCE: Whirlpool Cabrio top loading washer F1 Error

F1 means the control board is shot. Call whirlpool and they should take care of the parts and labor even though your machine is out of warranty.

Posted on Nov 27, 2009

  • 18 Answers

SOURCE: I have a whirlpool Cabrio, what does LF error code

The LF error is a water supply fault. Both water supplies must be connected and fully opened. The inlet hoses and valves both have strainers that may need cleaning as this could obstruct the water flow and also check that you don't have any water leaks. The unit requires a minimum water pressure to operate so anything that could prevent the unit getting this pressure will cause this fault. Hope this helps you out!

Posted on Nov 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When machine goes into final spin cycle it gives me a OL code


OL means the washer is overloaded or there is excessive drive load. Go to the link for a full explanation of the OL code and its repair. What might be causing the OL error code on my Whirlpool Cabrio washer...

Oct 12, 2016 | Whirlpool Washing Machines

1 Answer

What does an F-1 code mean on the display? washer will not start.


power problem

  • Whirlpool Fault Codes - AppliancePartsPros.com www.appliancepartspros.com > Appliance Repair Whirlpool Range / Stove / Oven Fault Codes: Failure Code: Fault Code Description: Solution: 4 Digit Failure Codes (for 2 digit codes see below) F1 - E0
  • Washer Diagnostic& Repair - F1 Error Code power supply ... www.youtube.com/watch?v=BAVS9mI3JLQ
    • BY APPLIANCEVIDEO.COM
    • 4 MIN
    • 65K VIEWS
    2014-02-07 · Troubleshoot your trusty Whirlpool Top Load Washer that has these following symptoms: F1 Error Code At: http://www.appliancevideo.com To ...
  • Whirlpool Cabrio f1 error and how to fix it https://whirlpoolcabriof1error.wordpress.com Control board W10189966 will work with the Whirlpool model numbers listed at the bottom of this page. These models include the Maytag Bravos and Kenmore Oasis.
  • whirlpool F1 code - Appliance Repair Forum forum.appliancepartspros.com > ... > Washer Repair
    • 68 POSTS
    • FIRST POST: 2008-07-28
    2009-09-29 · Discuss whirlpool F1 code in Washer Repair. "whirlpool cabrio washing machine displays f1 code. have already pushed cancel and restart to no avail.
  • Cabrio Washer by Whirlpool F1 Error Code - Facebook www.facebook.com/CabrioWasherByWhirlpoolF1ErrorCode Cabrio Washer by Whirlpool F1 Error Code. 793 likes. Got the F1 Error Code? Tell your story! Share ALL your issues with this washer to warn others...
  • Whirlpool Fault Codes - Appliance Help Online appliancehelponline.com/whirlpool.html Whirlpool Range / Stove / Oven Fault Codes: Failure Code: Fault Code Description: Solution: 4 Digit Failure Codes (for 2 digit codes see below) F1 - E0

  • May 04, 2016 | Whirlpool WTW8200YW Cabrio Top Load Washer

    1 Answer

    Ol code cabrio


    "oL" error code, even when unloaded - Fixitnow.com

    fixitnow.com/.../whirlpoolkenmore-cabrio-and-maytag-bravo-washers-th...
    Sep 18, 2010 - The "oL" error code in the Cabrio and Bravo washers means the ... is almost always caused by using non-HE detergent in this washer- see this ...

    Aug 17, 2015 | Washing Machines

    1 Answer

    Whirlpool cabrio model 6300sw1 won't aggitate and gives ol code


    It is overload error.
    "oL" (Over Load)
    Is the washer overloaded? The washer has attempted to fill •
    and begin the wash cycle. If the washer is overloaded, it will
    drain any water and detergent that was added during the fill.
    To correct the overload, remove several items and add
    detergent. Close lid and press START.

    Also try to download user manual from this site and check page 19.

    Download WHIRLPOOL CABRIO WTW6300SW1 Use Care Manual

    Sep 03, 2014 | Whirlpool Washing Machines

    1 Answer

    How do i fix the Ld code on a whirlpool cabrio top load washer WTW6200SW2?


    Troubleshooting Cabrio, Bravos, & Oasis Washer Problems Cabrio, Bravos, Oasis Washing Machine Overview
    Washer Components
    Diagnostic Mode & Tests ' Tips & Tricks Error Codes LF ' Ld ' uL ' oL ' Sd ' lid ' Po ' HC ' dL ' dU ' F1 ' F2 ' F30 ' F32 ' F40 ' F41 ' F50 ' F51 'F52 ' F53 ' F54 ' F70 ' F71 ' F72 ' F80 ' F81 ' F82 ' F83 ' F84 ' F85Always disconnect the washing machine's power supply before working on the appliance!Washing Machine Models That ApplyWhirlpool Cabrio Washing Machines
    WTW6200SW0, WTW6200SW1, WTW6200SW2, WTW6200SW3, WTW6200VW0, WTW6200VW1, WTW6300SB0, WTW6300SB1, WTW6300SB2, WTW6300SG0, WTW6300SG1, WTW6300SG2, WTW6300SW0, WTW6300SW1, WTW6300SW2, WTW6300WW0, WTW6340WW0, WTW6400SW0, WTW6400SW1, WTW6400SW2, WTW6400SW3, WTW6500WW1, WTW6600SB0, WTW6600SB1, WTW6600SB2, WTW6600SB3, WTW6600SG0, WTW6600SG1, WTW6600SG2, WTW6600SG3, WTW6600SW0, WTW6600SW1, WTW6600SW2, WTW6600SW3, WTW6700TU1, WTW6700TU2, WTW6700TW0, WTW6700TW1, WTW6700TW2, WTW6800WB1, WTW6800WL1, WTW6800WW1 WTW7300XW0, WTW7340XW0, WTW7600XW0, WTW7800XW0
    Maytag Bravos Washing Machines
    MTW6300TQ0, MTW6300TQ1, MTW6400TQ0, MTW6500TQ0, MTW6600TB0, MTW6600TB1, MTW6600TQ0, MTW6600TQ1, MTW6700TQ0, MTW6700TQ1, MVWB300WQ0, MVWB300WQ1, MVWB400VQ0, MVWB450WQ0, MVWB450WQ1, MVWB700VQ0, MVWB750WB0, MVWB750WB1, MVWB750WL0, MVWB750WL1, MVWB750WQ0, MVWB750WQ1, MVWB750WR0, MVWB750WR1, MVWB800VB0, MVWB800VQ0, MVWB800VU0, MVWB850WB0, MVWB850WB1, MVWB850WL0, MVWB850WL1, MVWB850WQ0, MVWB850WQ1, MVWB850WR0, MVWB850WR1
    Kenmore Oasis Washing Machines
    110.27092603, 110.27092602, 110.27092601, 110.27092600, 110.27087605, 110.27087604, 110.27087603, 110.27087602, 110.27087601, 110.27087600, 110.27086605, 110.27086604, 110.27086603, 110.27086602, 110.27086601, 110.27082605, 110.27082604, 110.27082603, 110.27082602, 110.27082601, 110.27082600, 110.27072604, 110.27072603, 110.27072602, 110.27072601, 110.27072600, 110.27062604, 110.27062603, 110.27062602, 110.27062601, 110.27062600, 110.27052602, 110.27052600, 110.27042603, 110.27042602, 110.27042601, 110.27042600, 110.27032603, 110.27032602, 110.27032601, 110.27032600
    NOTE: For All Error Codes
    First press PAUSE/CANCEL once to clear the error code.
    If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio, Bravos, Oasis Diagnostics Video) This will reveal any stored error codes. Then you will be able to better use the repair guide to fix the major malfunction. Now put the tea down and get to work!
    flood stop water supply hoses that may have closed internally?Is the drain hose sticking too far into your home's drain pipe (siphoning)?
    Is the pressure transducer hose kinked, disconnected, or punctured?
    Back to Top
    Press PAUSE/CANCEL to clear display. pressure transducer hose kinked, disconnected, or punctured?
    Press PAUSE/CANCEL to clear display.Washer Diagnostic Modes and Tests Washer Diagnostic Modes and Tests Washer Diagnostic Modes and Tests "Po" Pump Out (Lid Opened) Po flashes when the lid of the washing machine has been left open for more than 10 minutes. Close the lid to stop the drain pump.
    "HC" Hot & Cold Hoses Switched This code will appear at the end of the wash cycle to indicate that the hot and cold-water inlet hoses are reversed.
    "dL" Door/Lid Cannot Lock (Stored Error Codes F80, F82, F84, F85) Indicates the lid cannot lock.
    Check for items caught in the lid keeping it from closing completely.
    Is soap, fabric softener, or anything else keeping the lock from extending into the lid?
    The control detects an open lid switch, or cannot determine if the lid is locked. Test the lid lock connection to the washer's control board and lid lock resistance levels.
    Press PAUSE/CANCEL once to clear the code. "Ld" Washer is taking too long to drain water from the washtub
    (Stored Error Code F32) Check the following:
    Is the drain hose or pump clogged?
    Is the drain hose higher than 96" to reach the drainpipe?
    Is the Drain Pump Running?
    Is the pressure transducer hose kinked, disconnected, or punctured?
    Press PAUSE/CANCEL to clear display.

    Jun 07, 2014 | Whirlpool Cabrio WTW6600SBT Top Load...

    1 Answer

    The machine constantly displays the oL code when it r


    Hi Randall:
    If your the error reads OL, it's "overloaded" and you need to remove some items to delete this problem.

    Definitivelly, this flashes when the machine or motor control detects a load size that exceeds the washer's capacity. To clear the error open the door lid and restart the cycle by removing excess laundry. If error doesn't clears then unplug the washer for 5 at 10 minutes and check.

    Jan 30, 2012 | Whirlpool Cabrio WTW6600SBT Top Load...

    1 Answer

    Code ol


    Hi

    Error OL means overload. oL flashes when the machine/motor control detects a load size that exceeds the washer's capacity. To clear the error open the door lid and restart the cycle by removing excess laundry. If error doesn't clears then unplug the washer for 5-10 minutes and check. Hope this helps... Please post back if you need more information.

    Daniel

    Nov 16, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

    1 Answer

    I have a kenmore oasis elite top loader which is made by whirlpool. we have replaced the machine control panel and the electronic panel behind the dial. the washer is skipping time during the cycle then...


    Hi


    Thanks for using FixYa. Error oL means overloaded and it flashes when the machine/motor control detects a load size that exceeds the washer’s capacity. To clear this error you’ll have to open the door lid to clear display, remove excess laundry, then restart the cycle. Please do rate the solution if the issue is resolved or post a comment for further assistance.


    Thanks
    Rylee

    Aug 28, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

    1 Answer

    What does it mean when the machine gives an oL sign when starting the wash cycle?is it a quick fix and how much will it cost? It is a top load whirlpool cabrio washer.


    Hi


    Thanks for using FixYa. Error oL means overloaded and it flashes when the machine/motor control detects a load size that exceeds the washer’s capacity. To clear this error you’ll have to open the door lid to clear display, remove excess laundry, then restart the cycle. Please do rate the solution if the issue is resolved or post a comment for further assistance.


    Thanks
    Rylee

    Aug 26, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

    1 Answer

    Display shows oL - Top-load washer


    That oL is overload. You need to remove some clothes. On this model the motor can sense to much weight in the washer. If it does it without any clothes in there check for something jammed between the tubs.

    CABRIO SERVICE MANUAL


    If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

    May 09, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

    Not finding what you are looking for?
    Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

    Related Topics:

    359 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Washing Machines Experts

    Sal De

    Level 3 Expert

    2699 Answers

    Marvin
    Marvin

    Level 3 Expert

    84619 Answers

    Gerry Harvey
    Gerry Harvey

    Level 3 Expert

    1479 Answers

    Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...