Question about Brother GX-6750 Typewriter

1 Answer

RIBBON WONT STAY DOWN WHEN YOU TYPE - Brother GX-6750 Typewriter

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,306 Answers

Carrriage assembly could be broken, otherwise screw is popped out of gear in the right. With carriage all the way left, take out screw in the middle of white gear, pull out gear and pin, push down carriage top, insert pin in carriage and re-install screw.

Posted on Jul 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Swintec 7040 when I type a letter or word only write a half of the letter or the word and when I try to erase a letter or word the typewriter erase this but the erase ribbon stay in the same position...


There are a few possibilities. If only the tops are printing Press down on the platen to be sure it is fully seated in the side frame. The T/W may be in the overstrike ribbon mode Code period, comma or slash will get you out of that mode.

DickyO

Oct 11, 2011 | Swintec 7040 Typewriter

1 Answer

Tmailribbon will not stay down to type


Turn it off and on it should reset itself and the ribbon relocate.

DickyO

Aug 24, 2011 | Brother GX-6750 Typewriter

1 Answer

The piece that the ribbon cassette goes on won't lock in place


Do you mean the carrier wont stay in place or the ribbon wont stay.

Dec 10, 2010 | Brother ML-100 Typewriter

1 Answer

Hi, I have an IBM Wheelwriter 30 Series II. When I type text it does not type the bottom 20 % of letters. I changed the ribbon and made sure that the roller was securely locked down. Any suggestions? ...


yes in the carrier ribbon there is a adjustment of ribbon to fix it up and down.
take out the ribbon.
see the cam from where the ribbon carrige lift up.
in side that cam a adjustable screw from that screw you can adjust the ribbon hight.

Nov 25, 2010 | IBM Wheelwriter 30 Typewriter

1 Answer

Swintec 4000; type writer ribbon will not stay on and when it stays on - nothing prints out, and the ribbon jams up


Hello- Of course the cheapest fix, is to try a second ribbon. If you need one we have them at FJAproducts.com

Most often the reason the ribbon cassette will not stay in place is due to not being seated properly. I am sure you have taken it out a few times and re installed it, but that is "normally" the only reason it "jumps up" one more thing to check in the lever near the daisy wheel. if it got bumped or unlocked the daisy wheel your ribbon will not seat properly.

Good luck.

Duane ONeil
FJAproducts
800-982-9989

Jun 09, 2009 | Office Equipment & Supplies

1 Answer

Daisy wheel will not stay on wordsmith 100



CHANGING Changing The Ribbon Cassette 1) Move the print carrier to the center of the platen using the SPACE or BS key. 2) Hold the ribbon cassette on both sides and lift up the front portion (where the ribbon is exposed) to remove the cassette. 3) To insert a new cassette, place the back end of the cassette on the cassette holder on the carrier and gently press down on the front of the cassette unit it clicks into place. 4) Turn the ribbon feed knob counter-clockwise again to take up any slack in the ribbon. 5) Presss the CODE + = (SETTING) key.

Changing The Print Wheel 1) Move the print carrier to the center of the platen using the SPACE or BS key. 2) You will see a lever on the right side of the carrier. Pull this lever toward you and lift out the daisy wheel. 3) Place the daisy wheel into the slot with the characters facing the platen. 4) Push the lever back into position. 5) Press the CODE + = (SETTING) key.
It appears as though you have something that is preventing the print wheel from being locked in place by the release lever. It should make a snapping or similar noise when it is locked down.

Dec 10, 2008 | Smith Corona Wordsmith 100 Typewriter

1 Answer

Cd Ribbon Wont stay on


Try contacting a playstation consultant.

Nov 15, 2008 | Sony PlayStation 2 (PS2) Console

3 Answers

Changed Ribbon


Have you pressed the
'spider web' key (asterix in a circle) and + //

May 30, 2008 | Brother GX-6750 Typewriter

1 Answer

Ribbon Lift Eractic


Try the unit without the ribbon installed if the mech. seems to operate properly you may only need a new ribbon.  If the condition continues you may need a new ribbon motor or board.

Oct 22, 2007 | Lexmark Wheelwriter 1000 Typewriter

Not finding what you are looking for?
Brother GX-6750 Typewriter Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

James Cagle
James Cagle

Level 2 Expert

453 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...