Question about Indesit W 123 Front Load Washer

1 Answer

Faulty washing machine w123

After putting a load in the machine (w123) on program 4, it washes but stops at rinse. Then the programmer will spin around clicking.
Is the pcb dieing ??

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 97 Answers
Re: Faulty washing machine w123

Does the water empty from the machine? if not you will more than likely have something trapped in the pump. the best thing to do is run the grey outlet hose into a bucket, this will empty the machine. then tilt machine back (make sure it wont fall) then remove the plastic kick plate on the front bottom, behind this you should see the round plastic filter this will unscrew and pull out, you may need a couple of towels put on the floor as there is usually water left in the pipes. clean any debris and screw filter back in, should only need to be hand tight. replace kick plate and then give it try.
hope this helps


Posted on Nov 12, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Oko 72630. Why is it stuck on rinse cycle?

Could be several reasons:
- Selected the "Night cycle" program (means standing with the drum full of water, reason: too much noise in the spin cycle)
- Set to the "Rinse hold" (means standing with the drum full of water, reason: wrinkles on the clothes)

According to your description I think that this is not a failure otherwise error E20 will be appears on display.

Once the washing programme has come to an end, END illuminates on the programme progress display.
If RINSE HOLD was selected, the display beside the START/ PAUSE button flashes.
1. After a rinse hold, the water must first be pumped out:
- Either press the START/PAUSE button (the water is pumped out and the washing is spun according to the completed programme;
After the START/PAUSE button is pressed again, the spin speed can still also be changed during spinning), or
- Turn the programme selector to PUMP OUT and press the START/PAUSE button (the water is pumped out without spinning),or
- Turn the programme selector to SPIN or SHORT SPIN and press theSTART/PAUSE button (the water is pumped out and the washing is spun or gently spun).
At the end of this programme step, the END indicator will illuminate.
2. Open the door.
As soon as the DOOR indicator lights up green, the door can be opened.


Aug 15, 2015 | AEG Washing Machines

1 Answer

Wash doesn't progress to rinse and spin

This is one of 3 faults
1 you may have a problem with the heating cycle check element
2 you might have a water valve not working
3 there may be a program fault
These videos on how to change an element and water valve will help

Jul 22, 2013 | Bosch Classixx WFL 2066 Front Load Washer

1 Answer

Ariston A1435 washing machine. The prgrammes do not move on.Can select any cycle it washes but stays on the programme and does not move onto the rinse cycle have to manually stop and select rinse and spin....

If the program is put ON does the inlet valve open to let water IN. If so does it after the water is filled to the set level go to wash If yes , then after wash does it drain ? If all the above cycle is true then the program is working correct and a fault in the input can be the reason.
If however there is distruption of the sequence, then each input and drive must be checked to establish if the program controller or the input sensors are faulty.
Please give me a feedback

Sep 18, 2010 | Washing Machines

1 Answer

Machine wont stop washing on programme 9! went for days. Had the error lights flashing but that stopped.

If you select a rinse and spin programme and it completes the cycle, then I would say that the heater element is probably faulty, because the programme will not advance until the water has reached the correct temperature.
If it does not complete the rinse and spin cycle, then it is likely to be the control module that is the problem.

Feb 09, 2010 | Indesit W 123 Front Load Washer

1 Answer

Hotpoint wma76 stops and displays ON

Could be rinse water valve ..Faulty Solonoid coil

Nov 10, 2009 | Hotpoint WMA76 Front Load Washer

1 Answer

Washing machine won't rinse or spin

sounds as if you have a faulty lid switch, for safety reasons if the machine doesnt think the lid is closed it willnot spin/drain the waer out.

Feb 23, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Wash machine stays on wash cycle and doesnt go to rinse or spin

If the water is not getting hot, this will probably stop the programme advancing .Check heater.
Plz rate solution to prob.

Dec 10, 2008 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Bosh 1200 classixx does not finish the program, conditioner stays in the dispenser

I have cleaned the pipes going for rinsed water,plus the plumbing stuff like vertical pipe which has on top something like coupler for washing machine and dishwasher, here was problem. It was cloged up with rubish and becouse the pump could not make enugh pressure the machine has stopped in the moiddle of washing as it could not rinse.(Spin)


Sep 23, 2008 | Bosch Classixx WFC 2465 Front Load Washer

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 2 Expert

75 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides