Question about Neptune Washing Machines
Location of the circuit boards and removal tips please..washer does not spin..replaced the wax motor..need to replace board..can't find that thing!
ummmm, honestly ive never replaced just the board(im an authorized maytag servicer) so our replacements have always been new, and in this case the repair kit containing both board and motor. that being said, i cant see a reason as to why you couldnt relace just the board itself, ,Ireally never found the reason why the board would burn out, but, as far as repair kit im certain that they were trying to get all circuit boards and motors back to only one model, instead of having 5 or six different boards andmotors, this will bring them all to the most recent board and motor, never was an issue with themotor, jusat that you couldnt wire in the new board without the neew wiring. As long as its the same board i cant see why that wont work. as far as the "wax motor" that was a seperate issue burning out the Top control board, total seperate then your problem,., dont really see an issue with installing your "used board"
Posted on Apr 08, 2008
SOURCE: maytag neptune MAH4000AWQ
Check your exit hose spigot, it may be clogged. This is if your filter is all clean(ref manual). There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.
Rate me pl.....if helped. Click on 'thanks for trying' if not helped, your prob will be back for someone else to solve.
Posted on Jun 03, 2008
maytag neptune washers do have a motor problem and they have a kit to replace the motor and motor controller.
when the motor fails, it wont wash or spin. most units have a 5 year parts warranty and should be replaced with a free part, but you will have to pay an authorized servicer to do this.
if it is over 5 years then i would call maytag and see if they will help you with an authorization for repair.
most of the time they will provide the part for free. just call the 800 # and ask for help. they wont send you the part but might give you some help with the parts.
Posted on Jan 06, 2009
there are 2 wires going back to the board. They connect to a blue harness. Make sure their is continuity thru the harness. It connects to 3 out of balance swithches. Also check to see if lock light comes on.
Posted on Jul 07, 2009
check the spin enable switch. there is a seperate switch for the lock light and spin enable. if the actuator doesn't extend fully it won't hit the switch. or the switch is bad. It's located in the door latch assembly.
Posted on Jun 15, 2010
Tips for a great answer:
May 24, 2011 | Maytag Neptune MLE2000A Front Load Stacked...
on May 17, 2010 | Maytag Neptune MAH5500B Front Load Washer
on May 17, 2010 | Maytag Neptune MAH6500A Front Load Washer
? Unplug machine
? Remove the (2) screws holding center panel and remove panel
? Remove the (1) center screw holding the top panel located inside compartment above washer
? Remove the top panel to expose the door latch assembly
I hope this helps you.
Apr 25, 2011 | Maytag Neptune MLE2000A Front Load Stacked...
Mar 27, 2011 | Maytag Neptune MLE2000A Front Load Stacked...
Dec 23, 2010 | Maytag Neptune MAH5500B Front Load Washer
Jan 16, 2010 | Maytag Washing Machines
Nov 06, 2008 | Washing Machines
Jun 10, 2008 | Maytag Neptune MAH5500B Front Load Washer
Jun 02, 2008 | Maytag Neptune MAH5500B Front Load Washer
Oct 21, 2016 | Neptune Washing Machines
63 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: