Question about Toshiba TDP-MT200 Multimedia Projector

1 Answer

Lamp my lamp is finished.. where can I buy the chepest lamp for this projector?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Lamp - Toshiba TDP-MT200 Multimedia Projector Multimedia Projectors

There are some on ebay.

Posted on Jan 29, 2009

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

The machine starts, eventhe vent, but no image appears. All the lights, except the POWER SAVING one remain lights on.

  • Plug the projector into the wall and put it into standby mode. You should have already replaced the projector's lamp with a new LMP-P200.
  • Press the "Reset," left arrow, right arrow and "Enter" keys on the projector's control panel. Press them in the exact order listed here, one after another, and press each key for less than five seconds.
  • Turn the projector on with the "Power" button. Press the "Menu" key to enter the projector's menu settings.
  • Press the down arrow to navigate to the "Install Setting" menu and press the right arrow to select it. You should see the lamp timer at the bottom of the screen. If you have correctly reset the lamp timer, it will indicate 0 or 1 hours.
  • Press the "Menu" key to exit the menu system.

  • Read more :

    How to Reset Sony Projector eHow
  • Turn on your Sony projector after replacing the lamp.
  • Press the "Menu" button, go to the "Lamp Setting" option and select "Lamp Timer Reset." The projector should display a confirmation window asking, "Has the Projection Lamp Been Replaced?"
  • Select "Yes." You will receive a message onscreen saying, "Lamp Timer Reset Complete!" Select "Yes" again, and press the "Enter" button to finish.

  • Read more :

    Jul 02, 2015 | Sony VPL CS4 Multimedia Projector

    1 Answer

    Will not coming on ,standby light is orange temp and lamp light not on

    Just try to reset the lamp hour of your projector. For resetting the projector do the following.

    While simultaneously holding down MENU/HELP, ENTER and Down arrow button on the projector, Press STANDBY/ON on the projector.
    Remember one thing lamp hour reset is recommended only after the lamp replaced. Before going to buy a new lamp just reset the lamp hour and confirm that the projector doesn't have any other problem.

    If these doesn't help then check the lamp of you projector chances for lamp became faulty.

    Mar 19, 2011 | Sharp XR-10SL DLP Projector

    1 Answer

    Sanyo plc-xt16 Projector After the projector is turned on and the countdown finishes on initial start up the projector shuts itself off within 5 seconds. The fan runs for 1 minute and then the projector...

    It sounds like the lamp is going.
    Do you know how many hours of use are reported on the lamp?

    Many times these projectors have circuitry to shutdown when they suspect the lamp is near the end of life. Lamp hours vary and usually will go up to and even beyond expectancy, but there is occasions you can receive a bad lamp and have it blow in a matter of hours...not common but it does occur.

    I hope this helps,

    Mar 09, 2011 | Sanyo PLC-XT16 Multimedia Projector

    1 Answer

    Can you replace the Bulb only instead of buying the whole unit, if so where do i get one from? many thanks

    I don't believe that you can purchase this lamp as a bare bulb through official channels. It is an expensive lamp + projector and buying cheap copies is likely to be a risky business, definitely not supported by Barco. Prices seem to start at around £3500 GBP (ex VAT) or $5500 USD (ex TAX)

    If you are in the UK, here are the 1st two suppliers I found

    If you are in the US, again here are the 1st two.

    Given the fact that it is such an expensive lamp you should be able to negotiate a competitive price. I'd get on the phone to any potential supplier and ask them for their very best price rather than buying off the net.

    Feb 15, 2011 | Barco SLM G5 DLP Projector

    1 Answer

    Lamp and temperature light are lit but projector is working fine, should i be worried?

    The temperature lamp means it is overheating which will finish up cooking the LCD units, (blue first) and the lamp light is on as the lamp is about to expire.
    Clean the air inlet filters and replace the lamp.

    Oct 31, 2010 | Hitachi CP-S210 Multimedia Projector

    2 Answers

    Dell 3300 MP Projector


    I think this is a lamp issue. Even though your lamp might have an advertised time of 3000 hrs from Dell, it can fail and dim a lot earlier than that. Often within 1000 hrs a projector lamp's brightness can be reduced by up to 40%. Projector lamps brightness and lamp life varies according to how you use your projector and the environment it is in. Our company sells projector lamps and has created a YouTube video to help people get the most out of their projector lamps. You can see the video below. If you decide to buy a new lamp we have the lamp you need in stock at Projector Lamp Experts.

    Hope this helps..

    Jul 15, 2010 | Dell 3300MP Multimedia Projector

    1 Answer

    My projector keeps shutting down(sleep mode) after only being on for 5 minutes. how can I stop that from happening?

    The problem with you Projector is most likely the bulb. Here is a good guide on how to change out the lamp on your projector:

    I also suggest reading about the counterfeit lamps and buying the original lamp as recommended by the above link. You may find yourself troubleshooting further for no reason simply by buying an aftermarket replacement.

    Mar 04, 2010 | ASK Proxima C160 Multimedia Projector

    2 Answers

    Lamp does not glow

    Sound pretty much like a dead lamp. Problem could be a fan problem or heat sensor or power ballast. We supply lamps internationally so can assist if required as we ship world wide. Regards Kevin Andreassend

    Mar 21, 2009 | Sanyo PLC SW15 Multimedia Projector

    1 Answer

    Panasonic PT-AE900U Projector Lamp stops working (intermittent)

    since it has worked 1200 hours or even more since u have been resetting the counter! just change the lamp, resetting the counter does not make the lamp work or not work , it is only a reminder for the user to change the bulb when it should be & that u have some balance hours left to procure a new lamp!
    if the brightness is adequate, then it is a ballast problem & not lamp problem!
    buy a new lamp as u will anyway need to , fit it & it may solve ur problems permanently!

    Jan 27, 2009 | Panasonic PT-AE900U Multimedia Projector

    Not finding what you are looking for?
    Toshiba TDP-MT200 Multimedia Projector Logo

    Related Topics:

    91 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toshiba Multimedia Projectors Experts


    Level 3 Expert

    2236 Answers

    Electro Med Services...
    Electro Med Services...

    Level 3 Expert

    5327 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17129 Answers

    Are you a Toshiba Multimedia Projector Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides