Question about Whirlpool GU2400XTP Built-in Dishwasher

5 Answers

Washer stopped mid-cycle, water in the bottom of the tub. Circuit breaker popped due to over-load. Reset breaker and it immediately popped again. Could this be cause by a jam in the grinder assembly?

Posted by on

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My dishwasher just quit mid cycle. (still has water in it) It is a whirlpool partner 1. I checked the breaker and it wasn't tripped... but i reset it anyways. When I tried the dishwasher again it worked for a second and turned off. I have done reading about the thermo fuse but can't find it. Not sure how big of a problem this is.
Dishwasher is 5 years old.

Thanks,
Dale

Posted on Aug 18, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I hv a whrilpool quiet 2 dishwasher it will
not drain properly . whats wrong .

Posted on Sep 01, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I am having the same issue with mine. The house circuit breaker is fine, we reset it just to make sure. Other items that we plug into same outlet come on just fine. Just appears to be no power getting to the dishwasher itself since it stopped midcycle.

Posted on Aug 21, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Doubt that; sounds like you have an electrical short. If breaker will not reset it is due to a direct short. Leave breaker off and remove whatever panels to gain access to the electrical wiring. You should check your incoming power wiring to ground and isolate the source of the short.

Posted on Jul 02, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 784 Answers

Is there another outlet sharing the same circuit breaker?
1- Unplug the dis washer.
2- Turn on the Circuit breaker
a- if it didn't reset while there is some other outlet sharing meaning something shorted other than from the dishwasher.
b- if didn't reset with no other outlet shared the same circuit breaker, then your circuit breaker is bad.
c- if it resets with no other outlet shared the same circuit breaker, then ther is a shortage from your dis washer.
3- After address the issue with circuit breaker you will probably know if there is a problem with your dishwasher then we can go from there.

Posted on Jul 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My admiral washer does not work on wash cycle. It will rinse and spin on any cycle but wash


hi Marilyn.
this is what i have found but not sure if this will help you out,if not go to the link at the bottom and see if it helps you out.

Step 1

Make sure the washer's cord is plugged in to a functioning outlet if the Admiral washer won't fill with water. Check your circuit breaker to make sure the power is on and reset it if necessary. Reset the dial and start the washer again. Turn both of the washer's faucets on to full power. Untangle any inlet hoses to remove clogs. If this doesn't work, your hose filter screens could be clogged. Disconnect the hoses from the washer and clean the screens of any residue.

Step 2

Close the washer's lid completely if the Admiral washer will not agitate. The washer will not start if the lid is open. Restart the washer by setting the control dial to the desired cycle. Momentary pauses during cycles can be expected. You may need to wait a minute or two to see if the washer starts. Check the circuit breaker to make sure the washer is getting power. Reset the circuit breaker if necessary.

Step 3

Check and reset the circuit breaker as above if the Admiral washer will not spin or drain. Untangle any of the washer's hoses to allow water into the machine. Check your drains for clogs that may be preventing water to move into the washing machine. Close the lid and restart the washer. The washer will not start if the lid is not completely closed. If there are excessive soap bubbles in the washer, the washer may have locked up because of this. Wash the load again without adding detergent.

Step 4

Rearrange the laundry so it is evenly distributed if the Admiral washer stops or if laundry is still wet at the end of a cycle. Untangle any laundry from the center post in the wash tub. Select the correct water level for the amount of laundry. Select a normal spin cycle for jeans, towels or other heavy loads. Close the lid and start the washer.

Step 5

Check the hoses to make sure they are tightly connected to the Admiral washer if it leaks water. If they are loose, tighten them with a screwdriver. Make sure the drain hose is secured to the drainage area. Avoid putting too much laundry in your machine or soaking laundry for over 30 minutes.

Step 6

Make sure the Admiral washer is on a level plane if it is excessively noisy. If it is not on even ground, move the washer so that it is level. Remember that some washer noise is normal. Thin floors can cause the washer to vibrate and move about and the noise level may rise and fall depending on the speed of the cycle.

admiral washer does not work on wash cycle Google Search

Nov 25, 2017 | Washing Machines

1 Answer

Spin cycle trips house circuit breaker on my GE top loading washer


Hello,

The very likely reason the breaker trips only on spin is because the tub bearing is locked up on the washer since it is locked up its causing way excessive friction at the motor which causes the breaker to trip.Can you rotate the tub by hand or does it seem really hard to rotate by hand indicating that the tub is ceased up due to the tub bearing??


GENE

Oct 29, 2011 | Washing Machines

1 Answer

Bosch dishwasher shx55m with bottom tub full of water


The dishwasher really shouldn't pass any particles near large enough to clog the drain hose. It sounds more like a mechanical issue. Check the circuit breaker to make sure it's not tripped. See if you can hit a cancel button or something to make it drain. Try to run another cycle. If the computer is stuck or acting funny, trying cutting the power for a while, holding down a stop/reset/cancel button, or running a cycle that you don't usually run. I had this kitchenaid that would randomly refuse the normal wash cycle, but would run fine when you ran rinse only or something, then regular wash and everything would be fine again too. If the line somehow is clogged, there's a good chance it's right where the hose connects to the disposal or drain pipe.

Feb 18, 2010 | Bosch Integra® 500 SHX55M05UC Built-in...

2 Answers

LG WM2233H stop worrking in mid cycle, no displya


This has happened to me when the power has gone out. It doesn't display anything and all you can do is restart the cycle.

Jan 17, 2010 | LG WM2487H Front Load Washer

1 Answer

Kenmore eilite oasis


UL stands for an unbalance load where one side the tub is heavier than the other side.

when the code is displayed, it automatically unlocks the lid so you can go in and reposition the clothes to try and balance it. once you are done, simply press the start button again and it should continue again where it left off. if you push the stop button, it will drain the water and assume the cycle is complete.

unplugging it and replugging it in should allow you to do other wash cycles. press power and you should be able to select wash cycles.

if you still have no control, make sure you still have power at the outlet by plugging in a lamp and turning it on. if no power, find the GFI outlet that controls that outlet and reset it. if not on a GFI outlet, then check the circuit breaker panel for a popped breaker. reset it and power should now be restored.

Mar 05, 2009 | Kenmore Oasis HE 27082 Top Load Washer

2 Answers

Hi, my switch keeps going around and around without stopping


Hi I fixed the problem by removing the filter at the bottom right hand corner of the washing machine and removing 2 x £1 coins that had got stuck there

regards

Michelle

Jan 24, 2009 | Indesit W 123 Front Load Washer

1 Answer

Amana washer won't fill with water


1st I checked the power, compressor in garage had tripped the breaker to the washer circuit. This model has no bells or whistles to tell you if the power is on to the unit. Reset the breaker and unit works.
Thanks FixYa

Dec 22, 2008 | Whirlpool AWM5125/1 Front Load Washer

1 Answer

Het3 elite


remove the bottom panel below tha door. youll see the drain pump in the center,fronr of washer. there is a black hose going from the pump to the bottom of the tub. remove that hose. at the end of the hose there is a plastic ball that is supposed to seal the end of the hose. more than likely there is lint build up on the ball or around where the ball seal. clean the ball and the hose and reinstall. you should be fine after that

Nov 27, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Whirlpool GU2400XTP Built-in Dishwasher Logo

1,384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Mike

Level 3 Expert

4350 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...