Question about Samsung ML 2010 Laser Printer

1 Answer

How to replace rubber pickup

My rubber pickup is broken. I have a new one but can't figure out how to replace the old broken one. I saw instructions on how to replace the pickup on a ML-2510. It talks about moving some tabs etc. I tried but could not do that on my 2010. Is there any detailed instructions somewhere?-Bob

Posted by on

  • hillbob Jul 02, 2009

    I already have the new rubber pickup that I need. The old one broke. The problem is I can't seem to get the plastic holder apart to replace the rubber pickup. I push the small plastic tabs up and down and nothing happens. The sides just don't come off. Is there anywhere I can get a repair mannul with photos showing how to get the pickup holder off?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Samsung Master
  • 1,447 Answers

You buy xerox 3117 printer spare parts it is the same manufacturer printer but two brand name markating

Posted on Jul 02, 2009

  • Sazeed Computer
    Sazeed Computer Aug 18, 2009

    open your printer cover it have right side



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the procedure for installing new tires

That should be fairly straighforward. You won't need contact cement or anything (it'd make it nearly impossible to finish the job). First, get the new tires. Now peel the old tires off the wheels after removing the blade. It's easier, perhaps, if the wheels are off the saw... but that's a lot more to disassemble and reassemble and the tires CAN be replaced with the wheels still where they belong.

Clean up the wheels where the old tires used to be. Use whatever tooling may be required to get them VERY clean.

Now you can stretch the new tires onto the wheels with your hands, rolling them on like a giant rubber band. If your wheels are grooved, work the new tire into the groove as best you can. Insert two screwdrivers under the new tire and work both screwdrivers all the way around the rim - that lifts the tire and gets it to seat a little better. It also tends to help even out the stretch of the tire. BE CAREFUL not to stretch the tire too much, or it'll never stay in place.

Jul 30, 2014 | Delta 9" Band Saw Instruction Manual Model...

1 Answer

Need new rubber for my band saw wheels, model # 429.24250, dont know where to get them or if I still can?

What is the brand of your band saw? Well, regardless of the brand, you can find aftermarket replacement band saw parts online. I got my rubber tires from this site:

Sep 23, 2012 | Craftsman Old Band Saw Bottom Wheel...

1 Answer

I have an old Sears Jig Saw, model 110 25710, that has a broken blade. I need a new blad and instructions on how to remove the broken one, and replace it with the new one. Can you offer any assistance?

Take a look at the point of blade locking to the tool. Should be 2 hexagon bolts. Using the right size tool, unscrew them carefylly, pull out the broken blade, go to your local hardware store, and get a new one that will have the same size on the tail. ( the side that gets inside the slide on the saw). Slide the new blade to the saw, and tighten the bolts back but do it equally twisting them in turns, half a turn each time to keep the blade staying straight.
Whole thing should last no more than 5 min. ( Remember to keep the power cable unplugged all the time you make the change. Your fingers are priceless).

Sep 08, 2010 | Sears Saws

1 Answer

Broken drive belt on ryobi band saw, need

Just go to a well equipped hardware or auto parts store. Take the old belt with you so they can find an exact replacement. Good luck!

Apr 26, 2010 | Ryobi 9 in. Benchtop Band Saw

1 Answer

Water leak

open the back of your washing machine, you'll see a series of tubular figure. try to identify on which of the tube correspond to your soap tray, see if the rubber seal is broken or cut into pieces, if it does, then buy a replacement or if you don't have time, try to find an old rubber interior that has been used for vehicle tire, just cut same figure as the your old rubber seal and use it as a replacement

Oct 31, 2009 | Ariston Technologies Washing Machines

1 Answer


If you see a set screw where the blade goes, loosen it a few turns. Then run the saw, it should spit out the broken blade. If it has a manual release for the blade, press the release while tapping the blade holder.

Apr 29, 2009 | Craftsman 8.0 amp Reciprocating Saw

1 Answer

Broken arbor on lenox hole saw

Mine has a set screw some of them might threaded

Mar 15, 2009 | Lenox 48CT 3" Carbide Tipped Hole Saw

2 Answers

My printer hp laser jet 1320 not picking the paper from the tray.

Can you hear if the roller mechanism is kicking in? If you hear the roller moving but the paper is not even starting up the path, it's probably a worn pickup roller. If the solenoid is firing but the roller isn't turning then the feed roller shafts clutch mech is probably worn/broken and needs replaced.

Dec 18, 2008 | HP LaserJet 1320n Printer

2 Answers

Got a new part. don't know how to install it

I assume you either have recieved the separation pad or the paperpick roller. Here are instructions on how to replace both.

  1. Use the power switch to turn the product off and then unplug the power cord. Figure 1: Unplugging the power cord c00062340.gif
  2. Open the print-cartridge door, and remove the print cartridge. CAUTION: To prevent damage, do not expose the print cartridge to light. Cover the print cartridge or place it in a black plastic bag, if necessary. Also, do not touch the black-sponge transfer roller inside the product. Touching the transfer roller can damage the product.
  3. Locate the pickup roller. Figure 2: Removing the print cartridge, and locating roller c00062341.gif
  4. Gently release the small, white tabs on each side of the pickup roller by pushing them away from the roller, and then rotate the pickup roller toward the front. CAUTION: Use gentle pressure to release the small white tabs to avoid breaking them. Figure 3: Releasing the tabs c00062342.gif
  5. Gently pull the pickup roller up and out. Figure 4: Removing pickup roller c00062343.gif
  6. Perform one of the two following options:
    • Cleaning the pickup roller:
      1. Dampen a lint-free cloth with isopropyl alcohol, and scrub the roller.
      2. Using a dry lint free cloth, wipe the pickup roller to remove loosened dirt. Figure 5: Wiping the pickup roller c00062344.gif
    • Removing the new pickup roller from its packaging.
  7. Position the cleaned or replacement pickup roller in the slots on the pickup roller frame. NOTE: Circular and rectangular pegs on each side prevent incorrectly positioning the pickup roller. Figure 6: Positioning pickup roller c00062345.gif
  8. Rotate the top of the pickup roller into position until the white tabs on each side of the roller snap into place. NOTE: Touching the transfer roller can damage the product. Figure 7: Reinstalling the pickup roller c00062346.gif
  9. Reinstall the print cartridge and close the print-cartridge door.
  10. Plug the product in, and then use the power switch to turn on the product. Figure 8: Plugging the power cord in c00062347.gif
  11. Use the power switch to turn the product off and unplug the power cord. Figure 1: Turning off power and remove power cord c00062407.gif
  12. At the back of the product, unscrew the two screws that fasten the separation pad and frame to the product. Figure 2: Unscrewing the separation pad c00062408.gif
  13. Remove the separation pad and frame. Figure 3: Removing the separation pad c00062409.gif
  14. Perform one of the following two options:
    • To clean the separation pad: Dampen a lint-free cloth with isopropyl alcohol, and scrub the separation pad.
    • To replace the separation pad: Remove the new separation pad from its packaging
  15. Insert either the cleaned or replacement separation pad and frame and fasten it to the product with the two screws. Figure 4: Fastening the separation pad c00062410.gif
  16. Plug the product in, and then use the power switch to turn on the product. Figure 5: Turning the product on c00062411.gif

Nov 17, 2008 | HP LaserJet 3015 All-In-One Printer

3 Answers

Fuel delivery problem

There usually is a strainer in the gas tank. After 23 years, anything is possible. If you have a carburetor, replace it, or have it cleaned. If fuel injected, the big hose from the air filter could be damaged and shifting loose. If the engine doesn't see the right vacuum, it won't work right. Check all the little vacuum lines. Get a vacuum gauge, learn how to use it. Do a fuel flow test to see if your tank is clogged.

Aug 18, 2008 | 1985 Oldsmobile Calais

Not finding what you are looking for?
Samsung ML 2010 Laser Printer Logo

Related Topics:

604 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers


Level 2 Expert

167 Answers


Level 3 Expert

838 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides