Question about Roper RGX4634KQ Gas Dryer
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
i am sending you all the possibilities for your problem, check either of these causes ----and than let me know if it is solved----
Power from the house
Check to see whether there's power getting to the dryer. Is it plugged in? Check for blown fuses or tripped circuit breakers--your dryer uses two fuses or circuit breakers. The dryer could tumble but not heat if only one of the two fuses is blown. If you have circuit breakers, one of the two circuit breakers can trip, even if the two for the dryer are connected.
Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable.
On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.)
A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.
Posted on Dec 26, 2008
SOURCE: Roper Gas Dryer
On the front of the dryer there is a plastic hole cover. Take it off. If, when you start the dryer, you see it try to ignite (glow) but does not flame up, most likely the coils have gone bad. $20.00 online, $40.00 ata local store.
Posted on Dec 31, 2007
gass dryers have what they call an igniter it is either electronic or a ceramic stater check to see if it sparks or if in case its ceramic it glows look by the gas inlet and determin which one you have the ceramic igniter looks like a little torpito it just un clips the electronic starter takes a little knowlege allways disconect power before servicing good luck
Posted on Apr 12, 2010
The thermal cut-off , which is the small t-stat looking piece located at the top of the element housing ( on vertical mount elements ) or the far front of the element housing ( on horizontal mount elements ) , is usually the cause for no heat .
Posted on Aug 02, 2010
Tips for a great answer:
Aug 04, 2011 | Roper RES7646KQ Electric Dryer
Mar 24, 2011 | Roper RGX4634KQ Gas Dryer
If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.
if you dryer is gas check out this gas no heat tip....
If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.
check out this electric no heat tip...
Jan 19, 2011 | Roper RGX4634KQ Gas Dryer
If you are having problems with your
gas dryer not heating the most common problem is that the ignitor
goes bad. Even though it glows sometimes it is still not working
you dryer is gas check out this gas
If you have an electric dryer, you can
have many different things that can go wrong causing the dryer not to
out this electric
Dec 14, 2010 | Roper REX4634KQ Electric Dryer
Oct 22, 2010 | Roper Dryers
Sep 13, 2010 | Roper Dryers
Aug 13, 2010 | Roper REX4634KQ Electric Dryer
Nov 24, 2009 | Roper RGX4634KQ Gas Dryer
Jan 26, 2012 | Roper RGX4634KQ Gas Dryer
1,534 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: