Question about Sanyo VPC-T1060 Digital Camera

1 Answer

My camera won't turn on, but the lense is still out

My camera will come on but will automatcally turn off.IF a press the power button and quickly press the arrow, to review the pictures, it works, but anything other than that it will turn auotmatically off.i have a SANYO vpc-t1060. also my lense is still out and won't go back in.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

I think you have lens problem. You must fix your lens. I find someway that someone fix their lens error. At the other camera, the warning can be " turn the power off and on again' or "lens error". One post i have take at my blog. I hope is usefull

Posted on Jul 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Lense will not go back in


Remove the batteries from the Camera. Then press and hold the power button down for 45 to 60 seconds. Replace the batteries with new ones and install them in the camera. Then turn it on and wait until it finishes its normal warm up, then press the power button to turn it off. This should make the lense retract back to normal position. If the lens does not retract, contact the manufacturer for assistance with repair work.

Jul 07, 2011 | Canon PowerShot SD1000 Digital Camera

1 Answer

When I push the power button the lense moves in and out several times then the camera just turns off. I tried charging the battery and holding the power button down for 10 sec. but still does the same...


The power button has two purposes explanable;
1. A firm press and hold would shut down the entire device, where would be common feature for the camera to perform a system check to include the lense functionalilty.

2. A gentle press and release of the same power button should capture a snap shot only after the camera has been powered on, by the similar process as pressing firmly the power button

Remember

Pressing firmly the power button would shut down camera completely after a system check if only the camera was on.

Pressing firmly the power button when the camera is off would turn on the device by performing a system check also.

Important note
The camera when powered on would have an indicator light of ready to capture snap shots.
The camera would autoshut down when left on for an extensive duration without capturing snaps.
The instance of such would generate a camera check once more before powering off completely


The lense adds to the cameras feature capabilities of acquiring images. a function of the lense is capture an impressive image where the mechanism of drawing closer to the object is made possible by a moveable lense. The Olympus FE-340 Digital camera is powered by a battery requiring sufficient energy for a snap shot. keep in mind that, the camera can perform without the lense. However, the device is designed to automatically responded whenever the lense is required.

Important note;
1 a solution to the camera is with the source of energy in which instance batter power.
2.Dislogde the entire power area consisting of battery, check for improper installation; reinstall the battery in appropaitely noticing the installation indications of power supply. Cover the battery compartment properly, and charger afterwords.

Caution
1.Charge the battery for the entire duration known of a full charge.
2.Unplug thereafter when the full charge indicator is visible.
3.Try on the device for improvement in situation by taking photo snap shots

Dec 02, 2010 | Olympus FE-340 Digital Camera

1 Answer

My lens won´t retract. can see photos in Play mode, but will not switch to Record mode


Did it fall?
Try using a compressed air to blow off the small particles of dust which are arround the mechanism of the lenses(you dont have to dissaseble,just blow arround the lenses)
After that try playing with the batery(in-out while pressing the power button,so that the mechanislm of the lenses could come into place)
Hope it helps!

Oct 12, 2009 | Canon PowerShot S500 IXUS 500 Digital...

1 Answer

Lense was stuck out did what toothy said now the lense is stuck i


Hi!

Please follow the troubleshooting given below to resolve the issue:
(a) Turn off the Camera and remove the Battery then press and hold the power button for 30 seconds.
(b) Then, reinsert the Battery and turn the Camera ON. Please make sure that the Battery is fully charged.
(c) Next, press and hold the Reset button for 30 seconds located above the DC-in jack on the Camera using a sharp pointed object.

If the Camera doesn't operate normally even after performing all the above mentioned steps then service will be required.

Aug 23, 2009 | Sony Cyber-Shot DSC-P72 Digital Camera

7 Answers

Canon PowerShot SD780 IS camera lens error. :(...


I did the same thing and it works only be restarting it now but it works lol. I threw it agianst my bed . SO BEAT THE **** OUT OF YOUR CAMERA..then restart and it should work..*** made **** what can you say

Jul 28, 2009 | Canon PowerShot SD780 IS / IXUS 100 IS...

1 Answer

Hello I have a canon IXUS 960 IS. Yesterday when I was using the camera it only closed half way when powering the camera off. Now the camera doesn't open fully and when pusing the "play" button the power...


If the outside of the lense get dirty, those small particles may prevent the lense from opening and closing 100% as nomal times. I had the same problem with my Sony. Here is what I did.

1- I cleaned the outside(sides not the lense itself) of the lense.
2- While turning the camera off, I press on the lense (up and down motion) NOT too hard for a few times untill it either retracted all the way inn or most of the way in. If most of the way in, press the lense a little harder untill it retracts 100%. If you turn it back on, it should work as normal unless some mechanical part of the lense is broken or dislocated. When it fully opens, clean up the outside of the lense and keep it always clean for normal operation.

Good Luck!!!!!!!!

Jun 11, 2009 | Canon IXUS 960 IS Digital Camera

1 Answer

Changing lenses


hmm the correct way is to turn the lens to te left by pressing the release button, and keeping it pressed untill the lens is of (either turn the camera on the back, facing the NIKON brand on top , te bottom of the camera away form you and the internal flash and front lcd towards you

Jun 08, 2008 | Nikon D50 Digital Camera

1 Answer

Camera problems


Turns out the brand new batteries I installed were dead.

Mar 18, 2008 | Samsung Digimax S500 Digital Camera

Not finding what you are looking for?
Sanyo VPC-T1060 Digital Camera Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Cameras Experts

kakima

Level 3 Expert

102366 Answers

ray gallant

Level 3 Expert

42828 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Are you a Sanyo Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...