Question about Nokia 3110 Cellular Phone

1 Answer

Regulerly restart my nokia3110c was dropped in water so it hasbeen restart cotinue regularly & it is no going to standby mode

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 749 Answers

Hi...

There are still wet parts inside... have it checked to a repair phone shop and have it dry and check for other unseen problems.

goodluck... please rate..

Posted on Jul 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Taylor 8756-33. Which components operate in standby mode?


In standby mode, the machine just wants to keep the product refrigerated until it goes back into auto.

So, the mix cabinet needs to keep the product cool in the bottom of the machine, that requires the mix compressor and fans to run. The mix cabinet temperature is read by a thermistor probe and regulated by the (left side) logic board.

The product in the cylinders should go back to liquid form in standby, but we still have to maintain that safe food temperature, the motor and compressor will run periodically. If the machine is air-cooled a fan will run anytime the compressors run. If it is water cooled, water will flow through the machine when the compressor runs. The temperature in the freezing cylinders is read by a different thermistor probe and regulated by the logic boards.

Here is a link to all of the parts in a Taylor 8756.
http://www.softserveparts.com/c-1335911-parts-8756.html

f1efdb19-6ca9-408b-880a-c234233713ab.jpg

Jul 20, 2015 | Taylor Ice Cream Makers

1 Answer

The standby mode is not working tv will not go on


Fault with the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time.

Sep 08, 2014 | Sony Bravia L-Series KDL-32L5000 32-Inch...

1 Answer

ST-21c18 standby mode when switch to on..


pls. check for any blown fuse, if there is replace w/ thesame value. never replace fuses w/ ahigher value. then check power regulator & hrizontal output.

Jul 04, 2013 | Televison & Video

1 Answer

My washing machine would stop and beep and not advance to the next wash cycle and it was taking forever to fill up. I did the diagnostics and found it to be #49 which is a faulty hot or cold water valve. ...


Sorry for the very much delayed response due to site changes which modified the notification system.

Anyway, you should try holding first the WASH TEMP DOWN button then the POWER button until there's a beep. If it doesn't work, use WASH TEMP UP instead.

Make sure the Restart feature is turned on and the Recycle feature is turned off if all else fails. During the diagnostic mode use the WATER LEVEL DOWN button to turn RESTART on by pressing the said button until the LOW WATER LEVEL LED turns on. Use the WATER LEVEL UP button to turn RECYCLE off. The MEDIUM WATER LEVEL LED off indicates RECYCLE OFF. To set these modes in EEPROM the Advance button must be held while selecting Restart or Recycle. Power off the machine thereafter to complete the reset.

Oct 17, 2011 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

F61 error


The F61 error message is effectively a "protect mode" message indicating that a problem was detected and that the system hasbeen shut down to prevent further damage. This is typically caused by a bad output amplifier pac or regulator. If you can post the specific model number, I'll try to get you the part numbers and costs.

Dan

Aug 16, 2008 | Panasonic Home Theater System System

2 Answers

Stuck on standby


Unit is in protect mode there are a few problems that can trigger protect mode the most common is blown channel (shorted outputs). Sometimes one of the 15v regulators may go bad causing imbalance of supplys triggering protect mode. Also sometimes a bad solder connection could cause unit to go into protect also. I work for Denon authorzied repair center in Michigan if your nearby and Shipping to Michigan is economical let me know kstahl65@att.net

Feb 13, 2008 | Denon AVR-1804 Receiver

1 Answer

Startup


Going into protect due to either blown channel or probably a 15v regulator might be down which I have seen many times also. causing unit to go into protect.

Jan 21, 2008 | Denon AVR-3806 Receiver

Not finding what you are looking for?
Nokia 3110 Cellular Phone Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nokia Cell Phones Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

270rexton
270rexton

Level 3 Expert

782 Answers

Are you a Nokia Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...