Question about GE WBVH6240F Front Load Washer

1 Answer

Can't get the rubber gasket back on. - GE WBVH6240F Front Load Washer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Hi,

took mine apart. Remove both of the rings. The back one you may need to remove the concrete weight to get to the bolt. The front is just under spring tension. Then put the back one on first and you should be able to put the gasket on the front through the door.

Scott

Posted on Aug 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rubber gaskets for timex watches


The rubber gasket is the waterproof seal, to get the proper one you need to go to Timex or an approved repairer!

Nov 02, 2014 | Watches

1 Answer

Replace boot gasket


Hello, Remove the door hinges and plastic covers on the unused hinge screw holes on the opposite side of the door opening (door is reversible, so there are places to mount hinges left and right). Front panel will now snap out at top and lift off lower spring clips. One screw on each side will now release top panel and it will hinge up. Prop up with broom handle or something. Now you can get at everything. Rubber gasket is held onto drum with a cable loop and very strong spring. It rolls off the lip easily to disassemble but is VERY difficult to get back on without special tools or at least two people. Door side of rubber gasket is easy in comparison with rubber tabs inserted into slots and working the gasket into a groove. Hose clamp at bottom of rubber gasket to connect drain hose.

Thanks

Jun 10, 2010 | GE WSXH208A Front Load Washer

1 Answer

How do I change the headlight bulb?


rubber gasket can be peeled back to expose conector.

Feb 21, 2010 | 2001 Toyota Echo

1 Answer

Rubber gaskets came out


remove spring retainer ruber door boot remove the rubber.looking for the clamp loose it put the door boot back in the tub(drum)tie the clamp go revert the procedure(take out)good luck

Sep 29, 2008 | GE WSXH208A Front Load Washer

1 Answer

Repaired!


congratulations, it may help you if you use a bit of water with a bit of detergent as lubricant when snapping back the rubber gasket in place.

Jun 21, 2008 | AEG Lavamat 74640 Front Load Washer

3 Answers

Washer is leaking


Check the rubber bellow (gasket) around the door. This is the symptom of a door gasket that it starting to leak. Pull the rubber folds back and check the area where the gasket attaches to the wash tub. You may have a crack or tear. If the gasket is worn please replay back to this post and I can give you advice on how to replace it and where to get a replacement gasket.

May 14, 2008 | Whirlpool Duet GHW9150P Front Load Washer

4 Answers

Change rubber gasket


Remove the door hinges and plastic covers on the unused hinge screw holes on the opposite side of the door opening (door is reversable, so there are places to mount hinges left and right). Front panel will now snap out at top and lift off lower spring clips. One screw on each side will now release top panel and it will hinge up. Prop up with broom handle or something. Now you can get at everthing. Rubber gasket is held onto drum with a cable loop and very strong spring. It rolls off the lip easily to disassemble but is VERY difficult to get back on without special tools or at least two people. We used strong vice grips and much struggling and sweat, and #@*&%!&@ and finally got it on without damage to the new gasket. Door side of rubber gasket is easy in comparison with rubber tabs inserted into slots and working the gasket into a groove. Hose clamp at bottom of rubber gasket to connect drain hose.

Sep 05, 2007 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
GE WBVH6240F Front Load Washer Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...