Question about Jura Capresso Impressa E75 Espresso & Coffee Maker

1 Answer

A Ø43 mm rubber gasket broke - where do I get a new?

As a result of the broken o-ring gasket, no water is pressed through the grounds. All the water is poured directly into the wastebin. I managed to disassemble and identify that this gasket is broken, but now I have two requests:
1. Where do I get a new one? Its 3.5 mm material.
2. Is there a service manual available on the net?

Kind regards

Lars from Denmark

Posted by on

  • lpa4 Jun 30, 2009

    Found it myself. for those interested. They have also assemble/disassemble guides in German.



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 13 Answers

I have found seal/o-ring kits available on ebay Germany. Make sure you get the food grade lubricant to apply to the seals as well.


Posted on Jul 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Snowmobile manuals free

We have no manuals. Sorry.

Mar 15, 2014 | Winter Sports

1 Answer

When i store my bissell flip ease it leaks water all over the floor and it says you can store it with water in it.

It sounds like you have a faulty gasket and to find if this is the problem you will have to find where they connect and look at the gasket/ or it might be a little round rubber ring. If you do find a broken rubber ring take it to your local hardware store and have them match it up and then just put it on and you should be all set or the easiest solution to this is store it empty and fill it when you are going to use it.

Oct 25, 2009 | Bissell 52889 Flip-Ease All-in-One Vacuum...

1 Answer

Water pump

Clean all debris from the sending unit area of the tank.
Use a large flathead screwdriver and a medium hammer to turn the retainer ring counter clockwise.
There are three tabs sticking up on the ring, hit each of them intermitantly, The ring will turn about 1/5 th of a turn then it will be fully free.
Reassemble it the same way, Make sure the new rubber gasket is the propper fit.
If its not the same, Use the old one.


Jun 04, 2009 | 1997 Chevrolet Blazer

2 Answers

Took tank off and reinstalled 9 times - put new gaskets and rings in - but it leaks. Tank also wiggles a bit.

Go to the hardware store and get a tube of plumber's grease. Then grease up the gaskets and the rubber ring. Snug everything down and if it leaks snug it down a bit more

Apr 26, 2009 | Home

1 Answer

Water leak between tank and main unit

If it is leaking on top of the machine and under the water tank, there is a seal that needs to be replaced. Lift off the water tank. There is a large gray doughnut cap that will pop off. Take a screw driver and slip it under the outside of the cap between the machines top and pry gently up and it will pop that side. Go to the other side and do the same. Set the cap aside and take you index finger and stick it in the center of the black gasket. Lift up and if the gasket comes out with it you need to replace it. Clean the inside of the receptacle before installing the new gasket.
Once you get the new gasket, slip it at a slight angle(flat side up), then take your finger nail and run it around the outside edge of the gasket. It will slip in, then push it down. Take the cover and snap it into place. Your good to go.

Mar 24, 2009 | Solis SCDIG-5000 Coffee Maker, Espresso...

1 Answer

My hydrant is leaking water from the top and sounds like it is.

the little rubber gasket under the plastic cap is broken remove the plastic cp pull out the little white plastic piece flip it over remove the o ring and put in a new oen then put it back togeather.

Mar 15, 2009 | Halex Liquid Tight 90 Degree Elbow, 3/4"

2 Answers

Timing belt broke on my 2003 neon

what was it doing when the belt broke.... most times you just have the belt replaced and everything is fine.


Dec 19, 2008 | 2003 Dodge Neon

1 Answer

Focusing ring looseness on 50/1.2 M-Hexanon

did you see any rubber gasket on the ring.. this could be the one turn out to be loosen,

did you dropped or any kind of incident happened on the lens.

Nov 06, 2008 | Cameras

1 Answer

Frigidiare GLTF2940ESO front load washmachine

it has a fine ring clamp. find it and check it if its broke. they don't normally comes off easily. you will need a phillip screw driver to tighten it. unloosed it first, put the ring inside the gasket, then force the gasket gently to the metal round frame, then tighten the screw. i hope i was able to solve your problem. tnx

Feb 16, 2008 | Frigidaire GLTF1670A Front Load Washer

Not finding what you are looking for?
Jura Capresso Impressa E75 Espresso & Coffee Maker Logo

397 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

The Knight
The Knight

Level 3 Expert

75424 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ken Macumber
Ken Macumber

Level 1 Expert

12 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides