Question about Logitech Cordless Action (9633200403) Game Pad

1 Answer

I have no instructions

I just want to know how to program the controller

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: i have no instructions

In order to program the controller, you need to hold the button on the reciever for 10 seconds....during that 10 sec push a "face" button...usually 'X'. after a sec or 2 the green light on the reciever will go solid then turn off. now it should respond whenever you hit a button on your controller.

Posted on Jun 22, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

GT3-R -can

This is a dual frequency transmitter. (315/390) You need to select one button to program the TYPE 1 frequency of 390 MHz. Here's how:

Backwards compatable programming instructions for GT3-R dual-band remote: This is a 3 button remote, which can be used to operate up to 3 garage doors using IntelliCode radio controls. This remote is defaulted to operate the new IntelliCode 2 Genie garage door openers, but you can also program individual buttons to operate other IntelliCode 1 (pre 2011) models of Genie garage door openers made from 1998 to present. To change a button to operate a pre 2011 IntelliCode opener, the default IntelliCode 2 setting must be changed to IntelliCode 1. An LED light on the remote displays which mode the remote button is in: Red = IntelliCode 1 / Green = IntelliCode 2 To set one of the 3 buttons to be IntelliCode 1 (red), follow the instructions below:
  1. Select a button on the remote that has not been programmed.
  2. Press and hold that button for 10 seconds. Both Red and Green LEDs come on and stay on.
  3. Press the same button twice to toggle IntelliCode selection from IntelliCode 2 to IntelliCode 1.
  4. Press the same button again to confirm toggle. the LED should be Red. The IntelliCode selection for this button is set to IntelliCode 1.
You are now ready to program the remote to your garage door. Follow accompanying instructions for "Programming to IntelliCode 1 Genie garage door opener," or see below instructions: Programming Instructions: Gently press the Receiver Learn Code button on the power head receiver of your Genie garage door opener (motor head on ceiling in garage). This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. When pressed, a radio signal indicator light will start blinking red for 30 seconds. After pressing the Learn Code Button, press your transmitter button twice for your system to grab the frequency and code it in. (Keep the transmitter you're tuning at least 2 feet away from the power head while tuning.) Press the transmitter button once more to test the system and start your door moving.

Jan 06, 2012 | PC Game Controllers

1 Answer

I need some detailed instructions for programming the buttons on my Cyborg F.L.Y controller, with recommendations - - from someone familiar with computer gaming. i.e. a "Cyborg F.L.Y. for...

The best manual is on the support tab of the Programming Software.
If you need help in programming a specific key just let me know.

Also Saitek has som profiles now available on their page:

Hope it helps...

Mar 22, 2011 | Saitek Cyborg X Joystick

1 Answer

How do you program it

Go to and download any software you may need. Then...Win Vista or 7 Setup: Start>Control Panel>Printers and other hardware>Game Controllers>Then follow instructionsWin 200 or XP Setup: Start>Control Panel>Game Controllers>Then follow instructions

Dec 27, 2010 | Logitech Extreme 3D Pro Joystick

1 Answer

Instructions for programing game pad do not show how to program the pad. How can I get step by step instuctions?

Step by step instructions are too much to understand. I know how to set up gamepads... at least Logitech gamepads for now. I ve made several setups. You can ask me for setup for a game of your choice and i can try my best to help you. Visit this video for some of the most popular setups:

Apr 01, 2010 | Logitech Dual Action for Pc (963292-0403:)...

1 Answer

Can I use the joystick as a mouse?

Yes I also have the logitech attack 3 joystick and I found a very easy to use program. Go to and download the program. Then follow the instructions. Before you start the program, make sure that your joystick is plugged in. Then, pick the last joystick on the drop down menu on the main menu of the program. There you go! When you are done, just go to the bottom right corner of your computer screen, and right click on the picture that looks like a video game controller. Then click on exit.

Jan 19, 2009 | Logitech Attack 3 Joystick

2 Answers

Lost programming instructions for sidewinder 2.could u e-mail me a copy, or tell me how i can find online. thanks dean b

you can get the pdf online. go here:

Dec 02, 2008 | Microsoft SideWinder Precision 2 Joystick

1 Answer

UltraRacer playstation 2 controller programming

Here's the instructions on how to relocate buttons:

1. To assign one button (i.e. "R") to perform another buttom function (i.e.
"Z"): Press and hold the SET button for about 1 second to enter the
"FUNCTION SETUP MODE", the FUNCTION SETUP LED will illuminate and two beeps
will be heard.

2. Press the button (i.e. "R") you would like to reassign one time, the
FUNCTION SETUP LED will blink once and a single beep will be heard.

3. Press the new, desired function (i.e. "Z") one tim, the NORMAL LED
indicator will illuminate instead of the FUNCTION SETUP LED. Two beeps will
be heard. The setting process is now complete.

The UltraRacer will only return to its default setting when the buttons "A",
"L", and "R" are pressed at the same time BEFORE you turn on the console's
power. After about two seconds, the UltraRacer will generate three beeps to
acknowledge reset button configuration is set. To reset a particular button,
first press the SET button, then press the relocated button twice and then
press the SET button once more until the LED light goes off. THe button's
original function is used as a default button for further relocation.

These instructions were told to me bay a company selling these controls on AMAZON. I have been trying to reprogram mine and cant figure out where the "R" button is.

Nov 07, 2008 | Cables Unlimited InterAct UltraRacer Mini...

6 Answers

Trying to use controller for call of duty 4 on pc

All hail! Here is your solution. Download this profile complete with instructions. No hassle, no problems!

Nov 08, 2007 | Logitech Dual Action for Pc (963292-0403:)...

Not finding what you are looking for?
Logitech Cordless Action (9633200403) Game Pad Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Logitech PC Game Controllers Experts


Level 3 Expert

18259 Answers

Carlos L. Burgos
Carlos L. Burgos

Level 2 Expert

508 Answers

Are you a Logitech PC Game Controller Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides