Question about York Yankees Bedding MLB Comforter

1 Answer

Assembly manual for york 4180 home gym

Cabling instructions and which way does the rod for the weights go in.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

How the cable on Home gym4180 runs thru pullies

Posted on Dec 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Shimano EXAXSF1224A rod and want to know if there is a recommended sinker weight


This appears to be a Shimano Exage rod. Pl look at the lower end of the rod. You will see Max Lure weight. Mostly like say 5oz, 2oz, etc. The sinker plus bait must be less than this weight.

Jan 24, 2017 | Fishing

1 Answer

Machine goes out of balance & vibrates on spin cycle


Some models of top-load washers use tub dampening straps to cushion the movement of the tub during the spin cycle. There are four straps attached to the top of the tub and to each corner of the cabinet

Also There are four suspension rods that suspend the tub and allow the tub to free float. If the suspension rods are noisy, there will be a squeaking noise during wash. You can fix this by putting bearing (lithium base) grease in the cup that each rod rests in. If it continues to squeal replace all four rods the cups come with the rods, replace them as well.

If your washer has a loud banging noise during spin the balance weight may be loose. This weight is to counter act the weight of the motor so you will find the weight directly behind the motor. Sometimes simply tightening the bolts will fix your issue but if the bolts are stripped out get some bolts slightly longer than the original bolt to allow you to put a locking nut on the bottom side of the mounting plate. If the weight is broken replace it.

Lastly Washer vibration can be caused by a broken counter balance spring. Ur washer may be equipped with one or more counter balance springs which help to absorb the natural movement of the spinning tub. If a counter balance spring fails the tub might lean in one direction more than another and it will shake and cause vibration.










Mar 19, 2015 | Washing Machines

1 Answer

Explain the difference between "mass" and "weight" . if a NQ drill rod has a mass of 7,6kg per meter, what is the weight of a 3 meter NQdrill rod?


If the rod has a mass of 7,6kg/m then 3m of it will mass 22.8kg.

Mass it the amount of matter. Weight is the force exerted by the mass in a gravitational field. If you have an object massing 22.8kg, the mass of it will be 22.8kg whether you're on Earth, the Moon, or in outer space. It will weigh 22.8kg at the surface of the Earth, about 4kg on the Moon, and nothing (weightless) in outer space.

Aug 30, 2014 | Office Equipment & Supplies

1 Answer

Attachment for balance weight is broken


What model is it? Where on the rod is the break? Most of these counterweight rods just screw in to the mount. If you can extract the broken bit, and have a metalworking shop cut a new thread on the end, you are good.

Mar 22, 2014 | Optics

1 Answer

I have a 1997 F-250 HD. Driver door latch cable is broken at the handle end. I have a replacement cable, but need help figuring out how to remove the broken cable without breaking the plastic rod...


Door Handle/Latch Assembly NOTE: Due to the conversion from single 90-degree rod end shape to double 90-degree rod end shape, it may be necessary to remove more parts than the instructions indicate. This action will allow more maneuverability of the rod and ease the removal process.
Handle, Outside Door, Front Removal
  1. Remove the front door trim panel (23942) and front door trim shield (237A04) from the front door (20124). Refer to Section 01-05 .
  1. Disconnect the front door latch actuating rod (22152) from the handle link connector.
  1. Remove one nut and screw.
  1. Remove handle and pads from door.
----------------------
Some rods are double 90 degree rods, they require the handle or lach to be free when the rod is attached.
Some have plastic clips that slide onto the rod. they pop off sideways.

May 06, 2011 | Ford F-250 Cars & Trucks

1 Answer

How to remove piano keys from Roland KR 4700


You probably need to just clean the circuit board and the conductive rubber contacts. There are two per key to facilitate reading the key velocity.

Use 99% isoprophyl alcohol and Q-Tips to clean both the board and the rubber contacts.

A rod is inserted lengthwise to hold the hammer weights while removing the boards. Use dowels from each end inserted about halfway back between the keys and the weight rods. Use a 1/4 inch dowel rod.

You have to take out a few screws to remove the boards from the key assembly. Be careful of the cables.

Mar 17, 2010 | Yamaha NP 30 76 Key Lightweight Digital...

1 Answer

How do i adjust rotisserie counter-weight?


Once I have the meat on the spit rod and in the forks, I will lay it on the brackets on the grill and turn it by hand. You can feel when the heavy side of the spit rod rolls down. Put the counter weight on the opposite side (up side) and adjust the weight up or down until it turns evenly.

Dec 26, 2009 | BBQ Guys BBQ400C/G42 Grill

1 Answer

Porter cable roofing gun


The problem that you describe could be caused by three things. First remove the cylinder and look for a black rubber band around the cylinder about med section. There is an indention with holes where it is supposed to be. The band should fit snuggly so that it does not slip off during use. Secondly, check that the piston oring/plastic ring holds the piston in the cylinder without just dropping under its own weight. Third, the upper bumper could have a crack or missing piece. Remove it and check. (vinyl part in headvalve) Parts are available at dewalt repair center or www.toolpartsdirect.com. enjoy

Dec 06, 2008 | Porter Cable Cable RN175AR Reconditioned...

Not finding what you are looking for?
York Yankees Bedding MLB Comforter Logo

4,857 people viewed this question

Ask a Question

Usually answered in minutes!

Top York Sport & Outdoor - Others Experts

paulcarew

Level 3 Expert

2461 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a York Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...