Question about GE (JASHO96273)

1 Answer

GE profile fridge

The numbers for temp of fridge and freezer are not being displayed on front like they are supposed to. The fridge seems a touch warm but I can't tell what the temp actually is.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers
Re: GE profile fridge

Are numbers being displayed at all? If you want to confirm whether they are wrong or not, try putting a thermometer inside the fridge for about 10 minutes and check it against the temperature displayed. If it's wrong then it's probably the temperature sensor and would need to be replaced.

I suppose it's a long shot but could it be displaying 18 and feels more like 65? (Celcius vs. Farenheit)

Posted on Dec 06, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do I get my fb back to my real name using Shirley Steven at present because I was harassed and stalked? Tried everything but no go.

You should be able to go to your Facebook profile page, edit profile, find the name it currently shows, and then change it to what you currently want. Then you click save changes and your good to go. You have to do it from a computer and not on your cell phone, if that's what you were doing.

Nov 02, 2014 | Metrologic Instruments SFTP Relief Carving...

1 Answer

Cable stuck

Look at the above left. There should be a plastic lever (with a little nose to hold the plug in) reaching a few millimeters out of the front panel of your hub. Press it to the body of the plug and pull it out. If the lever is broken, use a small screwdriver, a needle or a paper-clip.
hth, Karl

Jul 29, 2013 | Cat5e Network Accessories

1 Answer

I have been on many sites with Cat 5 systems. What I cannot understand is why are the sockets numbered oddly i.e 1--6 2--7 3--8 etc. Instead of 1--2 3--4 5--6 etc.

Not sure if I understand your question.
Cat 5 (and higher) cables consist of four twisted pairs. The idea is, that disturbances by magnetic fields compensate each other this way. I suppose that the arrangement of the wire on the plugs and jack come from good ols analogue days, where the telephone-call was only on two wires (=one pair). To keep it as undisturbed as possible, the center of the plug (pins 4 and 5 on a rj45) was used. The next pair was spread over them and therefore used pins 3 and 6. Pair three was put on pin 1 and 2, and pai four on pins 7 and 8.
hth, Karl

Jun 17, 2011 | Cat5e Cat.5E Connection Box (512114)

1 Answer

Wiring this thing

The receptacle is numbered using a FRONT view (left to right, pin 1 - 8). Beware however, receptacles are wired from the REAR and hence the numbering will be inverted. Viewed from the REAR the numbering will be left to right, pin 8 - 1.
1 - white/orange 2 - orange 3 - white/green 4 - blue 5 - white/blue 6 - green 7 - white/brown 8 - brown

Apr 29, 2011 | Legrand On-Q WP3450-BE RJ45 Keystone...

1 Answer

My problem is i cant find my former facebook profile back and i dont know why can you help me please i need it

Your facebook profile is recoverable through the email address you signed up with. If you don't remember your password, you can recover it here:

Feb 09, 2011 | Network Accessories

1 Answer

How to put profile picture?

Click on "My Profile" in top right corner.
Then click on "Edit Profile" in top left corner.
Scroll down the page to the "Upload your Profile Picture" section.
Browse for your favorite picture.
Click on "Save Changes" blue button at the bottom of the page.

Aug 02, 2009 | Network Accessories

1 Answer

GE profile fridge

What you can do is either replace the fill tube, with a plastic one,, or you can install a filter.

May 01, 2008 | GE (JASHO96273)

2 Answers

GE Profile refrigerator TBX22pr

Just try to clean the water filter or replce it. Try to replace your ice maker my its old and need to be replace. If it is still not working, contact a appliance technician and let him check your refrigerator

Aug 06, 2007 | GE (JASHO96273)

1 Answer

Stacking Cable / SuperStack3 3870

Found this on 3Com website: The SuperStack 3 Switch 3870 family (3870-24 and 3870-48) can stack up to 8 units high. Stacks can be formed with any combination of 24-port and 48-port units, with a maximum of 384 (8 x 48) front panel ports supported. When connected together, a stack of units is managed as a single entity. All units in the stack need to run the same release of the operational version code (firmware). When units are stacked together, they operate in a master-slave relationship. One unit acts as a Master and the other units act as slaves. When looking at a stack of units, the master can be identified by looking at the Stack Master LED on the left side of the switch. The Stack Master LED is green for the Master. If the unit numbers are out of sync, go to the CLI command that allows users to re-number their units- system / control / renumber. This will re-number the units in the stack. It will take about a minute or two. The master is the only unit that has a visible command line interface (CLI) when a console cable is connected to it. If you connect the console cable to a slave unit, you will not see the CLI menu, but instead see slave status messages being displayed. The Master unit may not be unit 1.

Nov 21, 2006 | 3Com (3c17462)

Not finding what you are looking for?
GE (JASHO96273) Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Network Accessories Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers


Level 3 Expert

18258 Answers

Cindy Wells

Level 3 Expert

4719 Answers

Are you a GE Network Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides