Question about Griffin Technology iTrip Direct Attach FM Transmitter for Most Apple iPod Models

1 Answer

My i trip stops transmitting after about 1 min

It comes on works great then bloop its gone until i mess with it and it will start again and them 1 m later bloop

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same problem !!!

Posted on Apr 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I ran out of attempts to unlock the sterio on 2000 astra,what do i do now.any help would be great.


have you tried this?
Common problem. The safe message comes up when someone has input the wrong code.

There is an internal reset timer between each incorrect code input, this only starts to count down when theradio is powered up. Turn the power off before the timer runs down and you have to start again!

After the 3rd incorrect code you wait 10 mins, and then it doubles each time up to 640 mins for the 9th incorrect code!!

Simplest answer is drive around for a while (don't stall it!) until the display changes to 1 number followed by ----

Now simply press the number 1 on the radio until you get the first digit, it cycles round so if you miss the number you want just keep going until it comes round again.
Now use button number 2 for the second number, button 3 for the 3rd and button 4 for the fourth.

When you have the correct code, press and hold the AS button until you hear a bleep. Now it should be working.
Hope this helps.

Apr 30, 2018 | Cars & Trucks

1 Answer

Transmition stops after 4/6 min


what is your SWR, sounds like you need to tune the antenna, the radio is only doign what its supposed to do if the standing wave ratio (SWR) is too great

Mar 21, 2014 | Yaesu FT-77 Original Owners Manual

1 Answer

10 min. run time


Sounds like the vetilation hole in the gas cap is plugged, so fuel feeding out pulls a slight vaccuum in the tank. Flow stops until some air leaks in. Clean the cap or leave it loose.

Dec 02, 2017 | Garden

2 Answers

Ignition Cylinder if i replace this do i have to mess with any anti theft stuff


The antitheft will need reprogrammed when you are done. But it is fairly easy to do. Just leave the key in the run position until the security light stops flashing. (10 min).

Jun 17, 2010 | 1999 Oldsmobile Intrigue

2 Answers

How do I get the "change oil" message off my 2008 f 450 superduty?


Message center cluster
#1 press and release setup button until mess. cntr. displays"press reset to begin system check"
#2press and release reset button until cntr. displays"hold reset if new oil"
#3press and hold reset button for 2 sec. and release oil life should read 100%
#4 center displays"setup menu hold reset"

base cluster
#1 press and release trip/reset button until mess. cntr. displays"setup menu hold reset"
#2press and hold trip/reset button 2 sec. until mess cntr. displays"reset for system check"
#3 press and hold trip/reset button 2sec. until mess. cntr. displays"oil life XX% reset if new"
#4 press and release trip/reset button until mess.cntr.displays"hold reset if new oil"
#5 press and hold trip/reset button for 2 sec.and release to reset to 100%
#6 mess. cntr. breifly displays oil change set to 100%.

HOPE THIS HELPS

Feb 10, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

I have a gmc 3500 deisel,it starts and run great but out of no were it just shuts off.at stop ligyt or highway,doesn't matter.wait ten min. and it will start again,run for fifteen min. and die again.i...


check the camshaft and crankshaft sensors. If they get faulty (typical in GM cars) the PCM would shut down the engine. Happened the same problem to me and solved it by changing the crankshaft sensor.

Jan 24, 2010 | 1998 GMC Sierra

1 Answer

How do i stop my radio from making that bloop bloop noise after i key it


You are either describing a CALL TONE ( The Call Tone obtains others’ attention before you start talking) or the ROGER BEEP (When you turn on this feature, your two-way radio transmits a unique tone when you
finish transmitting. It’s like saying “Roger” or “Over” and lets others know you’re
finished talking.)

To shut off the roger beep, hold in the plus + button while turning the radio on.

The CALL TONE may or may not be a feature of your T5210 radio. I am unable to open the online manual for it to tell for certain. If it does have a CALL TONE feature you would access it by pressing the MENU button until you see a "CA" on the screen along with a number. Using the plus or minus button change the setting to zero, followed by pressing the menu button or the PTT button. The zero setting is equivalent to OFF.

To

Oct 01, 2009 | Motorola Talkabout T5210 2-Way Radio

Not finding what you are looking for?
Griffin Technology iTrip Direct Attach FM Transmitter for Most Apple iPod Models Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Griffin Technology Audio Players & Recorders Experts

Gary
Gary

Level 2 Expert

124 Answers

yadayada
yadayada

Level 3 Expert

80637 Answers

Brad Brown

Level 3 Expert

17328 Answers

Are you a Griffin Technology Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...