Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Fitting pump to hotpoint WF250

Can anyone advise how to fit a new pump to my hotpoint WF250 washing machine? I have been quoted £110 for the job!!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 353 Answers

Disconnect the machine hoses and all drain put it on its side you will see the pump usually help in place by 2 screws/ 2 hose clips/ 2 wire thats it pump should cost no more than approx.18.00

Posted on Jun 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint WF250 clothes coming out soaking wet after spin?


The fast wash cycle is for a reduced capacity load of approximately 3kg , it does not pump or spin long enough for a full capacity load

Jun 15, 2016 | Hotpoint Washing Machines

1 Answer

How do i fix a noisy spin cycle on hotpoint wf250


Hi.
A noisy spin cycle is usually because the bearings are rumbling and/or collapsed.
Unfortunately this is not a simple job and would require a service call and probably a workshop.
Good luck.
Nomess

Sep 28, 2014 | Hotpoint Repair Pcb / Module Wf240 Wf250...

1 Answer

Hotpoint WF250 lights are on but doesn't start


why would u replace the pump? i would check the door switch

Jul 10, 2014 | Hotpoint Washing Machines

1 Answer

Have a Hotpoint WF250 washing machine. Fitted new door lock switch, but door lock LED now constantly flashes & washing cycle does not start, even though water pump clicks!


TRY CHECKING YOUR MOTOR BRUSHES.IF THEY ARE OK IT IS PROBABLY THE PC BOARD LOCATED AT THE BOTTOM RIGHT OF THE MACHINE AS YOU LOOK FROM THE FRONT

Jun 05, 2013 | Washing Machines

1 Answer

My wf250 will not empty?


It is a common fault that the drain fails to work in most machines in a period of time and is the most problematic fault in a washing machine. In all occasions it is important that your observation is most important and so is vital to the identification /rectification and solution. If you have noticed that water has leaked then as the drain hose pump/valve and fittings are located on the underside of the machine it is important that you look for possible leaks here. In some cases the drain hose would be clogged at the drain end to outlet of the house and so there will be back flushing resulting in overflow to the outside. Also the drain pump/valve can be clogged. Now remove the drain hose clamps and remove the drain pump/valve, clean the drain pump/valve, use back flushing to clear off all dirt. Now test using power to see if this works and can be simulated. When refitting, the hose must be tightened properly. If the pump/valve does not work even with power then it must be replaced. If there is intermittent power to the drain valve/pump then the program controller unit is a suspect.

Cleaning a pump: http://www.youtube.com/watch?v=zKjKi50YBpI&NR=1&feature=fvwp

Finally the washer must be placed with a tilt- use a spirit level- so that all water will drain to the outlet port and thereby there is no residual water remaining.

Replacing the pump on a Bosch machine, please check this link for tips:

http://www.espares.co.uk/advice/washing-machines/a/7/1373/how-to-replace-the-pump-on-a-washing-machine-.html

Jan 23, 2013 | Hotpoint Repair Pcb / Module Wf240 Wf250...

1 Answer

I have a hotpoint aquarius WF250 1500 spin. The


Hi,

I've just had this exact same problem. Can you tell me if you have had any success with fixing it please?

Thanks!

Dan

Sep 17, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

My hotpoint aquarius wf250 won't do anything it lights up with wash symbol but doesn't fill or wash it doesn't make no noise or anything please help


open the top of washing machine and near the door on right side is a connector loose just push in and will work fine.

May 10, 2009 | Washing Machines

2 Answers

Belt on a hotpoint wf250


open it up, see wat thensions the belt, loosen that up and fit new belt. retension

Apr 19, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint wf250 drum wont spin


Well if you see the drum move in the wash cycle than the belt is still attached.Your door latch is the first thing to check.And the control board is the next and most likely problem.

May 24, 2008 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

freddyfox

Level 2 Expert

236 Answers

ptpumpman

Level 3 Expert

407 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...