Question about Zanussi FJS1225W Front Load Washer

1 Answer

Whirlpool not filling up with water OR SPINNING

Checked water hose that's fine but won't fill up with water. does drain though

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 353 Answers

Check your water valve that is your problem or pressure bottle blocked

Posted on Jun 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Whirlpool top loading washer won't fill completely


did you shorten the stand pipe for the outlet drain ?if not try putting a short extension on the top .

Nov 18, 2017 | Whirlpool Washing Machines

1 Answer

Washer won't fill water runs out bottom


either you have a bad drain hose or the drain pump has a bad seal behind the outer case

May 01, 2012 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

My Whirlpool Duet ht Washer starts washing fine, it drains then it starts flashing FH and wont take in water for the rinse cycle. It does this for every cycle, it will wash fine but after it drains and is...


The first thing I would check is shut off the cold water valve at the wall and remove the hose at the washer.carefully pry out the little screen in the inlet and clean well,reconnect hose and turn water back on FH is a water inlet issue I am hoping that what is happening is that when the washer starts its wash cycle it is probably filling with warm (hot) and cold water at the same time even though it might be mostly hot,but when it comes time to rinse (cold water ) there is not enough to make the computer happy and you get your FH error.. Hope this Helps,,If not your probley looking at a new fill valve assy

Sep 16, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My washer will not drain. At first it was giving the normal error messages like LF, so we had the drain piped to see if it was clogged. Now the washer fills up and does not drain. I have a Whirlpool...


Hi,


Thanks for using FixYa. Error LF means long fill, which flashes when the water level won’t change for a period of time after the valves are turned on or the water has disengaged the basket but control does not detect a water level change. TO resolve this issue check if the water supply is turned on and the hose screens are not plugged or kinked. If the water is not entering the machine then check the water valve, also check the pressure hose connection to the machine/motor control. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Aug 27, 2010 | Whirlpool Washing Machines

2 Answers

"LF" Long Fill Fault Code on Whirlpool Cabiro HE Washer


there is an electronic timer, did they mention how long the fill should take on average and when the timer signals fill time exceeded?

Sep 11, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Whirlpool washer - tub drains while it fills.


Your drain is to low. Make sure that the drain that your discharge hose is going into is at least as high as the washer. If not the water will drain out as fast as you can fill it.

Aug 15, 2009 | Whirlpool Washing Machines

2 Answers

My washer is not draining or spinning. It fills & agitates. whirlpool LLR8245DQ0 . i LOWERED THE DRAIN HOSE AND DRAINED IT BUT IT STILL DIDN'T SPIN


It may be the wire from pressure switch is either not receiving power through the switch or it may be broken? If that is ok then check timer.

Jul 29, 2009 | Washing Machines

1 Answer

Waher fills up and empties at the same time


you definalty have a drain hose issue, id bet that either your drain hose is lower the nte hunit itself or even connected to and outside drain sorce with out any "air gap/brake" i the drain line.. your creating a siphon action, you drain line should drain into a stand pipe no lower the n the back of the units console

Feb 20, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Dishwasher Accumulates Water When Off


Try turning water off to dishwasher and see if it stops it. If so, replace valve. If not check for a low drain hose loop, allowing drain water from sink to back up into dishwasher. Just raise drain hose as high as possible under sink and secure.

Nov 08, 2007 | Bosch 24 in. SGS43C12 Classixx...

Not finding what you are looking for?
Zanussi FJS1225W Front Load Washer Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

shaun taylor

Level 3 Expert

1527 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...