Question about Fantasia Viper (110927) Ceiling

1 Answer

Hi, first, the light stopped working. I replace the bulb (to no effect). When the power is switched on, the light flashes momentarily, showing the bulb is OK. Now the fan has stopped working too. I put a new battery in the remote (to no effect - the light on the remote comes on when you push the buttons). I tried to find the sensor on the fan to see if was obscured, but I can't find it (I lost the instructions, the fan is about 5 years old). Thanks, Dennis

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 235 Answers

The little black box inside the fan motor area is called the ballast and in most cases this is what goes out and needs replacement.

Posted on Jun 30, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My Sebo X4 does not switch on, when powered up two red lights flash momentarily. There was a buzzing from the black box underneath but that has now stopped. I changed the bag yesterday as it said it w

Your red lights flashing momentarily is normal start-up. The fact that your servo motor is operating tells you that you are getting power. If the vacuum motor does not turn on, you likely have a problem with the motor itself or the power supply board that feeds power to the motor. These items should be covered under warranty. However, if your vacuum is outside the manufacturers warranty, you can replace either of these parts fairly easily with only a phillips head screwdriver.I have included a link to the parts list for this machine. We do stock both parts.

Sep 24, 2014 | Sebo X4 Extra Bagged Upright Vacuum

1 Answer

Coleman lantern #5312 spiral bulb. problem: night light works ,battery fully charged. turn on hi knob; tube will flash momentarily then goes out, low setting will not come on. turn off and on several...

Most times the problem with these is that the batteries, though they show fully charged, are in poor condition.
Test: Count the cells in this unit and multiply by 1.2 test for that voltage, 4.8 is common, at the batterypack and turn the light on, if the voltage falls below 1 volt per cell, the battery protection circuit will engage and turn the light off. This is a battery problem.
If the voltage stays relatively steady, the bulb is the second item to be a common failure. Shine a flashlight across the base of the bulb where the 2 ends enter the white base. It the tubes are pretty blackened, your bulb is likely bad.
I don't have the specs for that switch, but it's a pretty simple device, it connects power from the batterypack to the inverter board or to the nightlight. It's simple to test with either an ohm meter (power disconnected) Or a volt meter, (Power connected)

Jan 12, 2018 | Coleman Electronics - Others

1 Answer

Grand prix front turn signals lights will not work but rears flash rapidly.

Definitely not the flasher, as long as it is flashing or blinking somewhere. Rapid flashing indicates a burned bulb, but since you already tried new bulbs in front, possibly bad bulb sockets, loose connectors, or a bad ground for the front bulbs. If you have a test light or voltmeter (multimeter), check for power at the socket when turns are on. If power then at the front, try new bulbs or trace the ground for those lights. If no power to the socket for turn signals, recheck wiring.

Apr 02, 2013 | 1995 Pontiac Grand Prix

1 Answer

96 chevy silverado, taillights just stopped working... nothing to cause this effect. they worked the night before. they just stopped. b/u brake hazards and turn signals all work. checked all fuses in the...

The turn signal switch in the steering column has a short in some models. Have someone watch your brake lights and move the 4 way flasher on top of the column from left to right without deploying the switch for the 4 ways. If your brake lights flash ,the harness needs to be replaced if they are still available. Harness around 300.00 plus labor.

Jan 10, 2013 | 1996 Chevrolet K1500

1 Answer

I have a Whirlpool side by side fridge freezer with ice maker and water dispenser which is about 3 years old. Model number I think is WSC5533. Recently I had an interior lamp bulb blow in the fridge which...

You may have a failing door switch which is causing this problem, if you remove the bulb and close the door, the the red light out? If so, its possible you bulb is fine, you door switch has failed.
I hope this helps

I’m happy to help further over the phone at

Jul 26, 2011 | Whirlpool Refrigerators

1 Answer

It doesn't show images in the monitor and at the same time it doesn't take pictures. thanks and more power!!!

your question is not clear. I see technical point of view. you first should disable flash mode (flash off mode), many case the flash circuit continuously force powering on whenever camera switch on and user can not use momentarily. But you can use only in day light condition if the problem condition. If not, it is shutter unit is effective that can work properly. The shutter unit is inner lens unit assemble. You should then consult to local camera tech. Thank and best regard!

May 21, 2011 | Nikon Coolpix 4300 Digital Camera

1 Answer

Im looking for a wiring diagram for the brake lights. 93 GMC Jimmy. The brake lights stopped working and i have tryed the fuse, bulbs and the brake switch. What else could it be? Thanks 93 Jimmy...

What happens if you have the key in the run position, you foot on the brake and you wiggle, pull, push the turn signal lever. Also try turning the hazards on and off slowly. All while keeping an eye on the brake lights to see if they come on momentarily.

I'm pretty sure the brake and turn signal share the same bulb If so we know that the bulb and the wiring from the switch to the bulb is fine. If there is power into and out of the brake switch than it is reasonable to assume that the problem is in between the brake switch and the turn signal switch if not the switch itself.

I’m happy to assist further over the phone at

Oct 19, 2010 | GMC Jimmy Cars & Trucks

1 Answer

I have a Chevy 2500 4X4 with brake lights not working. I have all other lights working. I only have one brake light working when I turn on the right turn signal then my left brake light will work. What's...

What year?

Sounds like a turn signal switch. Earlier models would use the same bulb for the brake and turn signal. The turn signal switch will interrupt power to the brake light and route the signal to either the left or right bulb depending on with way you where turning. Usually you can wiggle the turn signal switch and get the brake light to work momentarily when this is the problem.

Newer vehicles use a lighting module that looks for inputs from the turn signal switch and brake pedal switch and then decides where to send power. This module is also know to go bad.

I’m happy to assist further over the phone at

Oct 11, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

Timer on my 200W transformer is working but lights will not turn on manually or by timer. when i turn on with manual switch they flash on for a second then turn off. i am just under 200W for total...

You posted under Intermatic-malibu power packs.
Wattage of bulbs must match wattage of power pack or bulbs and power pack will burn out.

Your power pack might be damaged beyond repair.

For information on Intermatic/Malibu power packs showing troubleshoot steps, replacement trippers, useful links, warranties and tips:

Aug 23, 2010 | Malibu ML200RT - Low Voltage Power Pack...

2 Answers

LED does'nt work on tail light but conventional bulb is working

Maybe your LED bulb is defective and so you need to replace that LED bulb with a new good quality one.
I can recommend you search for a LED High Bay Lights which are of high quality and cost-effective.These bulbs are reliable and save a lot of power.
You can also find here simple and easy to use plug and play LED lamps.
Hope this will help!


Apr 11, 2017 | 1995 Honda Civic

Not finding what you are looking for?
Fantasia Viper (110927) Ceiling Logo

431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fantasia Dryers Experts


Level 3 Expert

81294 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Brad Brown

Level 3 Expert

17433 Answers

Are you a Fantasia Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides