Question about Belkin Wireless (F5D7130) 802.11g/b Wireless Access Point

Open Question

Belkin f5d7130 cant connect

Ive set up tis router as instructed in the manual but i cant connect to the device wirelessly to do any sort of setup.

the lights are as follows power is green, wlan is green but flashing and the lan is flashing orange

any ideas how to fix this issue ive tried to plug it direct in to the switch that controls our company internet and to a hub connected to our network but still no change

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Mtnhorse
  • 1 Answer

SOURCE: Wont connect to the internet

Try this, assuming you're using Internet Explorer: Go to Tools > Internet Options and select the Connections tab. Does it show your old dial-up connection in the list? If so highlight it and click on REMOVE. Close IE and re-open it. It should now use the Belkin LAN connection.

Posted on Aug 18, 2007

Ad
madansakre
  • 51 Answers

SOURCE: Belkin USB Plus Hub - F5U304

PLEASE INSTALL THE DRIVER CD IN YOUR PC AND RECONNECT IT WILL DEFENITELY SHOW...

THANK YOU...

Posted on Jan 05, 2008

stif_NEC
  • 441 Answers

SOURCE: http://192.168.1.1 is not working anymore? i cant set up the router

Try resetting the router, press the reset button at the back for 10 seconds, after that release the reset button and then unplug the power of the router, then wait for 10 seconds and then turn it back on.

After that try accessing the IP of the router 192.168.1.1 (if this did not work try 192.168.0.1,this varies on the model number of the router). Or follow the same steps you have done previously.

Posted on Aug 16, 2008

  • 18 Answers

SOURCE: connect belkin f5d7130 to homehub 1.5

You need to connect all pc's and homehub to a switch so they can talk to one another. Then use the AP as a wireless access point to connect all wireless laptops, and connect the AP to the switch with ethernet cable, and you have a network. Just make sure that only your HH or AP supplies IP addresses or they will clash.

Posted on Oct 19, 2009

  • 566 Answers

SOURCE: does anyone know where i can get the setup

You can download the manual and quick instalation guide for the F5D7130 Wireless Network Access Point
from Belkin. No software is needed nor is supplied with the access point.

If you bought the access point bundled with the network card F5D7010, then the disk that came with it would have the drivers for the card. You can get them from Belkin also. Click here

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Don'I have a Toshiba tv model 29L1350U how do I connect it to my wireless router


The Toshiba 29L1350U is not a Smart TV. It doesn't connect to any router (wired or wireless). You'll need some sort of media streaming device that can connect to the router. This could be something like a Roku, Google ChromeCast or Amazon Fire stick that connect to an HDMI port or one of the similar set-top boxes. Even a Blu-ray player with streaming capabilities would work. Follow the directions for powering up the device and then connect to the network using the directions in that device's setup.

You can find the specifications and manual for the 29L1350 on the Toshiba support page: http://support.toshiba.com/support/modelHome?freeText=3528910 . Click on the Manuals & Specs tab.

I wish that I had better news for you.

Cindy Wells

Jun 06, 2016 | Toshiba Televison & Video

1 Answer

Manual for belkin wireless router n150 )f9j1001v1)


Are you struggling with belkin router setup, check out this article and follow the instructions to fix the problem.
How Can Install Belkin Wireless Router Belkin Router Setup Help

Dec 04, 2011 | Computers & Internet

1 Answer

How do i unlock my internet so i can acess wireless off it


Are you trying to connect a wireless capable device to a wireless connection?

If Yes of if unsure, to connect a WiFi capable device to a wireless connection you will need the following: a cable modem, a wireless router, Ethernet, a WiFi capable device.

You would connect the wireless router to the modem follow the installation manual instructions for the router to properly setup the router, different brands require different setup procedures.

Once the router is up and running find the SSID (wireless network name you gave the wireless router during setup) for the wireless signal. Click on the SSID in the list of available networks and enter in the passphrase when prompted to.

If all is successful you should connect to a wireless network

Let me know if that helped or if you need additional information or clarification.

I’m happy to help further over the phone at https://www.6ya.com/expert/james_d4449ffdf318a2c3

Oct 27, 2010 | Internet Compaq Evo N600C Laptop

1 Answer

Cant get connected with my belkin router...all i can get is "connected with limited access


HI

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} How to quickly install and use your Belkin wireless G router

1. Step 1 Position your Belkin wireless G router.
Place your wireless G router in a wide open and central location. Don't connect the power plug into the router, yet. Make sure your computer is turned off.

2. Step 2 Connect all the devices.
Find the Ethernet cable that connects your PC to the modem. Unplug the Ethernet cable from your PC and insert it into the wireless G router's WAN port. You should have an additional Ethernet cable that came with your router. Take this cable and plug one end into one of the LAN ports on the router. Then connect the other end to your PC's Ethernet port.

3. Step 3 Turn on your modem, router, and PC.
Plug the power plug adapter into the modem. Turn on the modem. It'll take approximately 30 seconds for the modem to boot up. Connect the power plug adapter to the router and the other end into a power strip or outlet. Like the modem, it'll take about 30 seconds for the router to boot. Turn on your PC.

4. Step 4 Verify lights are on for your devices.
Make sure the following lights are on for your router: power, WAN, and LAN light. If you don't see any of them lit, confirm these devices are turned on. Make sure the Ethernet cable connections are installed correctly.
Step 5 Install and configure software.
Use the setup wizard application to configure your Belkin wireless G router. Set up features, such as creating your password and setting up your time zone. Continue to follow the setup wizard so you can configure ?other settings

Oct 18, 2010 | Belkin N1 Wireless-N Wireless Router

1 Answer

Security


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} How to quickly install and use your Belkin wireless G router 1. Step 1
Position your Belkin wireless G router.

Place your wireless G router in a wide open and central location. Don't connect the power plug into the router, yet. Make sure your computer is turned off.

2. Step 2
Connect all the devices.

Find the Ethernet cable that connects your PC to the modem. Unplug the Ethernet cable from your PC and insert it into the wireless G router's WAN port. You should have an additional Ethernet cable that came with your router. Take this cable and plug one end into one of the LAN ports on the router. Then connect the other end to your PC's Ethernet port.

3. Step 3
Turn on your modem, router, and PC.

Plug the power plug adapter into the modem. Turn on the modem. It'll take approximately 30 seconds for the modem to boot up. Connect the power plug adapter to the router and the other end into a power strip or outlet. Like the modem, it'll take about 30 seconds for the router to boot. Turn on your PC.

4. Step 4
Verify lights are on for your devices.

Make sure the following lights are on for your router: power, WAN, and LAN light. If you don't see any of them lit, confirm these devices are turned on. Make sure the Ethernet cable connections are installed correctly.

5. Step 5
Install and configure software.

Use the setup wizard application to configure your Belkin wireless G router. Set up features, such as creating your password and setting up your time zone. Continue to follow the setup wizard so you can configure  other settings.

Jul 23, 2010 | Belkin N Wireless Modem-Router F5D8633au4A

1 Answer

I cant connect to the internet


How to quickly install and use your Belkin wireless G router 1. Step 1
Position your Belkin wireless G router.

Place your wireless G router in a wide open and central location. Don't connect the power plug into the router, yet. Make sure your computer is turned off.

2. Step 2
Connect all the devices.

Find the Ethernet cable that connects your PC to the modem. Unplug the Ethernet cable from your PC and insert it into the wireless G router's WAN port. You should have an additional Ethernet cable that came with your router. Take this cable and plug one end into one of the LAN ports on the router. Then connect the other end to your PC's Ethernet port.

3. Step 3
Turn on your modem, router, and PC.

Plug the power plug adapter into the modem. Turn on the modem. It'll take approximately 30 seconds for the modem to boot up. Connect the power plug adapter to the router and the other end into a power strip or outlet. Like the modem, it'll take about 30 seconds for the router to boot. Turn on your PC.

4. Step 4
Verify lights are on for your devices.

Make sure the following lights are on for your router: power, WAN, and LAN light. If you don't see any of them lit, confirm these devices are turned on. Make sure the Ethernet cable connections are installed correctly.

5. Step 5
Install and configure software.

Use the setup wizard application to configure your Belkin wireless G router. Set up features, such as creating your password and setting up your time zone. Continue to follow the setup wizard so you can configure  other settings.

Jun 10, 2010 | Belkin Wireless Pre-N (F5D8230-4) Router...

1 Answer

My router cant connect to the internet through the modem and i cant acces my rfouter setting cause cant install it


How to quickly install and use your Belkin wireless G router 1. Step 1
Position your Belkin wireless G router.

Place your wireless G router in a wide open and central location. Don't connect the power plug into the router, yet. Make sure your computer is turned off.

2. Step 2
Connect all the devices.

Find the Ethernet cable that connects your PC to the modem. Unplug the Ethernet cable from your PC and insert it into the wireless G router's WAN port. You should have an additional Ethernet cable that came with your router. Take this cable and plug one end into one of the LAN ports on the router. Then connect the other end to your PC's Ethernet port.

3. Step 3
Turn on your modem, router, and PC.

Plug the power plug adapter into the modem. Turn on the modem. It'll take approximately 30 seconds for the modem to boot up. Connect the power plug adapter to the router and the other end into a power strip or outlet. Like the modem, it'll take about 30 seconds for the router to boot. Turn on your PC.

4. Step 4
Verify lights are on for your devices.

Make sure the following lights are on for your router: power, WAN, and LAN light. If you don't see any of them lit, confirm these devices are turned on. Make sure the Ethernet cable connections are installed correctly.

5. Step 5
Install and configure software.

Use the setup wizard application to configure your Belkin wireless G router. Set up features, such as creating your password and setting up your time zone. Continue to follow the setup wizard so you can configure  other settings.


or folow the link you will get all your solution

http://www.google.co.in/images?hl=en&rlz=1R2SKPB_en&q=linksys+router+setup&um=1&ie=UTF-8&source=univ&ei=PzPPS_e-I4a1rAeYxryFAQ&sa=X&oi=image_result_group&ct=title&resnum=4&ved=0CCEQsAQwAw

Apr 21, 2010 | Linksys WRT300N Wireless Router

1 Answer

Setup Wizard says theres a problem connecting to network device


with a new router I would suggest to to start from scratch and do it manually, here's the manual
and I strongly suggest you give netgear a call if the manual setup does not work. feel free to post back although do it after following the manual setup instructions on page 11.
also provide more info like, isp and operating system and we'll try to help out.

Dec 24, 2009 | NetGear WNR2000 Wireless Router

2 Answers

Cant get online with ps3 since ive purchased a new NETGEAR dg834


Hi, please perform the steps below to configure settings on the router:

Please follow the steps on a computer connected to the router so as to check the network key:
1. Open the browser (Internet Explorer, Mozilla Firefox or Safari).
2. Access the router usually by typing 'http://192.168.1.1' or 'http://www.routerlogin.com' in the address bar.
3. Login to the router with the Username as "admin" and Password as "password" (please note that Username and Password are case sensitive).
4. Click on Wireless Settings (under Setup) from the left menu.
5. Check if WEP (Wired Equivalent Privacy) or WPA-PSK (Wi-Fi Protected Access Pre-Shared Key) is selected under 'Security Options'.
6. If WPA-PSK is selected, copy the code entered in the passphrase.
7. If WEP is selected, copy the code entered in the key that has been checked.
This is the code required for connecting the wireless computer to the router's wireless network.

In some cases, for security reasons the passphrase might show as asterisks. In this case type a new Password and click apply. You will then have to use the same Password for all the wireless devices connecting to the network.
Please scan for the wireless network on the PS3 and connect to the wireless network.


Let me know if you need any fruther help.

Sep 09, 2009 | NetGear DG834G Router

1 Answer

Pass word to secure the wireless


  1. Then u have to setup ur router first
  2. Turn off the power on your computer.
  3. Securely connect an end of an Ethernet cable to your computer, as shown.
  4. Securely connect the other end to any of the router's four LAN ports.
  5. Connect a second Ethernet cable from the router's single WAN port to the modem.
  6. Make sure the modem is connected to the jack or cable to the Internet that was set up by your ISP.
  7. Start your network in this order:
    1. Turn the modem power off.
    2. Turn the router power off.
    3. Turn the modem power back on. Wait two minutes until the lights are stable.
    4. Turn the router power back on. Wait one minute until the lights are stable.
    5. Turn the computer power back on.
  8. Open an Internet browser, and type http://192.168.0.1. If a "Configuration Assistant" appears immediately, then do not follow the rest of these instructions. Follow the Configuration Assistant instructions, instead. Once you are finished, test your Internet connection by browing online,
  9. Type admin for User Name, and password for Password. (Older routers use 1234 as the password.)
  10. Click OK. This logs you into the router.
  11. Click Setup Wizard, on the left of the router settings page and set up your router , click wireless tab and setup wireless security for your connection
  12. that would fix your problem..

Nov 20, 2007 | Belkin Wireless G Plus MIMO (F5D9230-4)...

Not finding what you are looking for?
Belkin Wireless (F5D7130) 802.11g/b Wireless Access Point Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2263 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...