Question about Xerox Phaser 7400/DXF Laser Printer

1 Answer

Do not print full cover page

I change rainbow imaging unit nad when I trying to print full cover page it deasnot print and reset and start all over again doing the same untill I cancel the print.
This was doing when old IU's were over but less coverage pages were print while full coverage pages did not print.
It keeps doing the same with the new IU
what shall I do?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 110 Answers

Have you tried the Transfer Unit.? That is what transfers the ink to the paper before it is fused by the fuser.

I would guess Trasfer Unit if it is all colors.. If it is one colr then maybe laser unit.

Posted on Sep 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I refill the cartridge of my canon mp496 printer.I print images and everithing is ok but the ink lamps are orange .I don't know what to do ! Please ,help me !!


One of these reset methods should fix the problem

This is the procedure I used for an MP470. It is basically a modified version of that previously posted for the MP460.

1. Disconnect the power cable.
2. Hold down "On/Off" button.
3. Reconnect the power cable.
4. With the power button still down, press the "Stop/Reset" button twice.
5. Release the "On/Off" button.
6. The printer is now in "factory mode".
- wait until "idle" is displayed.
7. Press the right arrow button (next to the "OK" button) repeatedly until "Shipping Mode 3" is displayed.
8. Press the "OK" Button
9. Wait until "Without Cleaning" is displayed and then presss the "Stop/Reset" button once. (I pressed the ok button after Stop/Reset button on my MP470).
10. A test page should print.
11. Open the cover.
- the cartridges should position themselves at the far left - the cartridge removal location.
12. Disconnect the power cable.
13. Remove both cartridges.
14. Close the cover.
15. Reconnect the power cable.
16. Press the "On/Off" button once.
17. Wait until a "Replace Cartridges" message is displayed.
- insert cartridges.
18. Wait until the printer is operating in its normal mode. The display shows the normal start menu (ie: Copy).
The ink levels have been reset.
- check by going to printer>properties>maintenance>view printer status



this is what i had to do to get it to work with canon mp460
1. Disconnect the power cable
2. Hold down power button
3. Reconnect the power cable
4. With the power button still down, press twice the "Cancel/Stop" red button
5. Release the power button
6. The printer is now in factory mode...(wait about 30 seconds until it says "idle")
7. Press the down arrow (next to the "OK" button) until it says "Shipping Mode 1"
8. Press the "OK" Button
9. Now with it displaying "Without Cleaning" press the power button
10. A test page should print
11. Now open cover
12. Disconnect the power again
13. Take both cartridges out like normal
14. Close cover
15. Reconnect power cable
16. Press power button
17. Replace cartridges







MP-160 is different from MX300 so I tried my best with it...
The main solution is to reset the entire printer:
1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Jul 01, 2011 | Office Equipment & Supplies

1 Answer

I have replaced the imaging unit and it still asks for a new one how do i reset it


folow the steps please:

Checking replaceables

If you experience frequent paper jams or printing problems, check the

number of pages the machine has printed or scanned. Replace the

corresponding parts, if necessary.

1. Press Menu until System Setup appears on the bottom line of the

display and press OK.

2. Press the left/right arrow until Maintenance appears and press OK.

3. Press the left/right arrow until Supplies Life appears and press OK.
4. Press the left/right arrow until the item you want appears and press OK.

• Supplies Info: Prints the supply information page.

• Total: Displays the total number of pages printed.

• ADF Scan: Displays the number of pages scanned using the ADF.

• Platen Scan: Displays the number of pages scanned using the

scanner glass.
• Imaging Unit, Transfer Belt, Fuser, TransferRoller, Tray1

Roller: displays the number of pages printed each item.

5. If you selected to print a supply information page, press OK to confirm.
6. Press Stop/Clear to return to ready mode.

when you reach the imaging unit reset it then try, it should work then

May 19, 2011 | Samsung CLX-3175FN Printer

1 Answer

Replaced ink compatable cartridges in my cannon pixma 350 and now its telling me to replace them cause the ink is empty Help


This will reset your cartridges to full settings. I have found these resets to work on many Canon models. Try the top one first.


This is the procedure I used for an MP470. It is basically a modified version of that previously posted for the MP460.

1. Disconnect the power cable.
2. Hold down "On/Off" button.
3. Reconnect the power cable.
4. With the power button still down, press the "Stop/Reset" button twice.
5. Release the "On/Off" button.
6. The printer is now in "factory mode".
- wait until "idle" is displayed.
7. Press the right arrow button (next to the "OK" button) repeatedly until "Shipping Mode 3" is displayed.
8. Press the "OK" Button
9. Wait until "Without Cleaning" is displayed and then presss the "Stop/Reset" button once. (I pressed the ok button after Stop/Reset button on my MP470).
10. A test page should print.
11. Open the cover.
- the cartridges should position themselves at the far left - the cartridge removal location.
12. Disconnect the power cable.
13. Remove both cartridges.
14. Close the cover.
15. Reconnect the power cable.
16. Press the "On/Off" button once.
17. Wait until a "Replace Cartridges" message is displayed.
- insert cartridges.
18. Wait until the printer is operating in its normal mode. The display shows the normal start menu (ie: Copy).
The ink levels have been reset.
- check by going to printer>properties>maintenance>view printer status



this is what i had to do to get it to work with canon mp460
1. Disconnect the power cable
2. Hold down power button
3. Reconnect the power cable
4. With the power button still down, press twice the "Cancel/Stop" red button
5. Release the power button
6. The printer is now in factory mode...(wait about 30 seconds until it says "idle")
7. Press the down arrow (next to the "OK" button) until it says "Shipping Mode 1"
8. Press the "OK" Button
9. Now with it displaying "Without Cleaning" press the power button
10. A test page should print
11. Now open cover
12. Disconnect the power again
13. Take both cartridges out like normal
14. Close cover
15. Reconnect power cable
16. Press power button
17. Replace cartridges






MP-160 is different from MX300 so I tried my best with it...
The main solution is to reset the entire printer:
1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Mar 27, 2011 | Canon PIXMA MX350 Wireless All-in-One...

1 Answer

How can i reset the Ink Level on Canon MP240


Here are three methods that have worked on Canon printers. Have no fear. None of these will cause damage if they do not reset the ink counter. Once reset you will have to monitor the cartridges by weight, as the system will always show them to be full.

The first is basically a modified version posted for the MP460.

1. Disconnect the power cable.
2. Hold down "On/Off" button.
3. Reconnect the power cable.
4. With the power button still down, press the "Stop/Reset" button twice.
5. Release the "On/Off" button.
6. The printer is now in "factory mode".
- wait until "idle" is displayed.
7. Press the right arrow button (next to the "OK" button) repeatedly until "Shipping Mode 3" is displayed.
8. Press the "OK" Button
9. Wait until "Without Cleaning" is displayed and then presss the "Stop/Reset" button once. (I pressed the ok button after Stop/Reset button on my MP470 to get the test sheet).
10. A test page should print.
11. Open the cover.
- the cartridges should position themselves at the far left - the cartridge removal location.
12. Disconnect the power cable.
13. Remove both cartridges.
14. Close the cover.
15. Reconnect the power cable.
16. Press the "On/Off" button once.
17. Wait until a "Replace Cartridges" message is displayed.
- insert cartridges.
18. Wait until the printer is operating in its normal mode. The display shows the normal start menu (ie: Copy).
The ink levels have been reset.
- check by going to printer>properties>maintenance>view printer status



this is what i had to do to get it to work with canon mp460
1. Disconnect the power cable
2. Hold down power button
3. Reconnect the power cable
4. With the power button still down, press twice the "Cancel/Stop" red button
5. Release the power button
6. The printer is now in factory mode...(wait about 30 seconds until it says "idle")
7. Press the down arrow (next to the "OK" button) until it says "Shipping Mode 1"
8. Press the "OK" Button
9. Now with it displaying "Without Cleaning" press the power button
10. A test page should print
11. Now open cover
12. Disconnect the power again
13. Take both cartridges out like normal
14. Close cover
15. Reconnect power cable
16. Press power button
17. Replace cartridges






MP-160 is different from MX300 so I tried my best with it...
The main solution is to reset the entire printer:
1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Mar 09, 2011 | Canon PIXMA MP240 All-In-One InkJet...

1 Answer

My Brother HL-2040 paper led light won't stop flashing, the paper's not jammed or anything, I just put in a new toner, too. I tried doing what someone else said about opening the cover and holding Go until...


Hi. The reasons listed in the manual that cause the LED to flash normally are:

Front cover is open
Close the front cover of the printer.
Back cover is open
Close the back cover of the printer.
Paper jam
Clear the paper jam. See Paper jams and how to clear them on page 6-5.
If the printer does not start printing, press the Go button.
No paper fed manual feed slot
Put the paper in the manual feed slot. See Printing on plain paper, bond paper
or transparencies from the manual feed slot on page 1-10 or Printing on thick
paper, labels and envelopes from the manual feed slot on page 1-13.
Memory full
The printer memory is full and the printer cannot print full pages of a
document. See Solving print problems on page 6-15.
Print overrun
A print overrun occurred and the printer cannot print full pages of a document.
See Solving print problems on page 6-15.
Drum Error
The corona wire needs to be cleaned. See Cleaning the corona wire on page 5-14.

If you check out page 6-5 it tells how to clear the paper jam from the rear of the machine! A point often missed.

Check out the website below if you don’t have a copy of the instruction manual =

http://welcome.solutions.brother.com/BSC/public/files/dlf/doc002089/US_Eur.pdf

If all else fails, try a reset of the printer Drum & Page counter:
  1. With printer tuned on.
  2. Press and hold the “internal button” behind front cover, until all LEDs illuminate.
  3. Make sure Drum light is off, then release and close front cover.
Hope some of this helps………..Please post a response back here and let us all know if it works?............Regards, Cornwellnet (UK)

Jul 12, 2009 | Brother HL-2040 Laser Printer

1 Answer

Dell Printer 1720dn - Unable to reset drum counter..


"Press & hold the cancel button untill all lights start flashing in a sequence and then i release the button and close the front cover." "DO NOT release the button, but continue to hold down it while you close the front cover.

Printer offline: Right click on your printer in the "Printers and Faxes" folder and "UN Check" use printer off line,

May 11, 2009 | Dell 1720dn Laser Printer

2 Answers

Imaging unit warning led


First enter into tech mode by pressing clear stop/exposure contol«/clear stop/exposure control» . Select the service mode function using the copy quantity and the zoom key and then press the start key.(The functions are shown in the order of d,c,A,and F.)
Now code c2 is(0) change to(1) press start.
Also to reset the counters, go code c6 and change it from (0) to (5) and all counters will be reset as soon as the machine is switched off and then on again.
good luck.

Oct 21, 2008 | Minolta EP1030/1030F CS/PRO Copier

1 Answer

Change Image Drum light blinking


You have to reset the drum counter. Leave the front cover open Press and hold the "cancel" button until all the lights flash in sequence Close the front cover You should be good fro another 30 - 40 thousand copies. Hope it helps Ed

May 22, 2007 | Dell 1710n Laser Printer

Not finding what you are looking for?
Xerox Phaser 7400/DXF Laser Printer Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Michel

Level 2 Expert

97 Answers

Xeroxrep

Level 1 Expert

33 Answers

Philip Hughes

Level 2 Expert

75 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...