Question about Washing Machines

1 Answer

Nec nw-891 washing machine will not complete the programmed cycle

Nec nw-891 washing machine will not complete programmed cycle, but stops at end of either wash or rinse cycles. why? ie. program for 2 x wash cycles, 2 x rinse cycles & 2 x spin; machine stops after 2 x wash cycles and you have to restart the machine at the rinse cycle. again it stops at the end of the 2 rise cycles and has to be re-started.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Apparent malfunction in the timer circuits. Specific Component replacement not available.

Posted on Jun 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a nec nw-691, when you put it on spin cycle it brings error message --lid open??? plz help


Yuo might try making sure it is still level but I'd just try using a lower spin speed. How have to use "gentle spin" when I wash towels or my washing machine has errors and stops. If still too damp just use a gentle spin only cycle once more to finish the job.

Apr 16, 2015 | Washing Machines

1 Answer

My NEC NW-81R top loader when it turns on does not make the usual introductory series of beeps and is stuck at a spin cycle but won't start. The only button that works is the power button...any...


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Check this link to replace the inlet valve:

http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Thank you for using fixya.

Sep 24, 2011 | Washing Machines

1 Answer

I am having a problem with my NEC NW752 Washing Machine. It runs through the cycle but will not drain the water. There were no kinks in the hose and when we hooked another washing machine it worked fine....


chances are that your daiwood / nec unit has a bad drain pump or perhaps the unit is not level or the drain hose is to high for the pump to pump out the water lastly

if you remove the front of the unit where the pump is located as you will see in the link I sent you there is a trap that may need to be cleaned out it has a hand screw cap that you can open and clean try that first before replacing the pump i sent you in the link NEC WASHING MACHINE WATER DRAIN PUMP NW752 NW891 NW652 NW 891 NW 81R eBay

Mar 04, 2018 | Washing Machines

1 Answer

NEC washing machine model NW-891 can't get past the rinse cycle it just keeps on rinsing, emptying and rinsing again and again


It is the problem of the board, which can be fixed, by a specialized mechanic. Contact a nearby mechanic with sufficient tools. Sometimes you will have to replace your board which will be expensive. In that case, if your unit is an old one, try to get an exchange.

Jul 05, 2010 | Washing Machines

1 Answer

I also have an NEC NW-452 Washing Machine,it has stopped working completely,doesn't power-up at all,the User Manual troubleshooting guide is no help at all,I tested it it with a Digital Multimeter to see...


take the top off and follow the mains cable to where the cable is connected in the terminal block it could have come loose or the cable itself is at fault check the wire from the plug terminals to the terminal block eric

Dec 27, 2017 | Washing Machines

1 Answer

No response after starting cycle


could be the door interlocking device

Aug 26, 2009 | Washing Machines

1 Answer

The NW - 891 NEC washing machine does not finish the third cycle or drain?


Our nec washing machine nw 891 leaks water into drum when finished , I think it needs new washers, is this hard to do?

Aug 06, 2008 | Washing Machines

3 Answers

Washing machine nec nw-652


i am having the almost the same problem with what i have, if it is turn, the water will just keeping on pouring in non stop, it does matter wether it is wash, rinse, dry or spin the water will just keep on pouring in at all time, it is not a good machine at all.

Sep 09, 2007 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

79847 Answers

Brad Brown

Level 3 Expert

17147 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...