Question about Craftsman 25cc Gas Line Trimmer

1 Answer

Replaced fuel lines. How long should the large and small fuel lines be in tank

Posted by on

  • Anonymous Mar 17, 2014

    model Ge type 2

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

The fuel line with the filter in the tank should go the full length of the
tank
return line 1/2 to 3/4 of a inch in the tank
when changing the one with the filter ,replace filter with new one

Posted on Jun 30, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

2strokeguy
  • 183 Answers

SOURCE: need to know how fuel line end in fuel tank on a

Your Craftsman trimmer is made my Poulan/Weedeater and uses 2 different sized lines. The smaller diameter line is the fule supply line and runs from the pickup filter in the tank to the supply side of the carb. The supply side is usually the lower of the fuel nipples on the carb. Make sure to put enough line in the tank so the filter can drop to the lowest point of the tank while you are trimming. The larger diameter line is the return line, and will connect to the nipple on the carb that is closest to the primer bulb. From the factory, the return line went into the tank and had a small clear plasted connector on the end to prevent it from slipping back out of the tank. This fitting does not connect to anything in the tank, it is merely a return line. If the return line fitting is missing, just make sure to leave a couple of inches of line in the tank. If the filter is missing, you MUST replace it...it will save you from having to clean the carb out every 10 minutes of run time.
Good luck!

Posted on Aug 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel line routing on craftsman blower vac serial number 9528n06419


The small line goes to the fuel filter and the larger one is the vent to the fuel tank. The primer should have a large and small outlet and then you can put the small to small and the large to the large outlet. The fuel line from the tank goes to the carb. Hope this helps.

Apr 29, 2015 | Craftsman Garden

1 Answer

Cant figure out which hoses hook to which valve lines on a 1986 yamaha riva moped scooter fuel petcock


Large line is fuel, from tank to petcock. Large line from petcock to Carb. small line is vacumn from intake manifold to petcock (small spigot). suck on this line & make sure Gas comes through Large line to Carb.

Dec 16, 2013 | 1985 Yamaha XJ 700 X Maxim

2 Answers

Need to replace both fuel lines on My BVM200 LE leaf blower, 1 large and 1 small fuel line, can You tell what size they are??


On your blower, it looks like the small line supplies fuel to the carburator which will be connected to the fuel filter in the tank, and the large line looks like the fuel return line.

http://www.ereplacementparts.com/poulan-type-gas-blower-parts-c-16962_31724_131359.html

Jul 19, 2011 | Poulan Pro 25CC 2Cycle Gas Blower

2 Answers

I have a weedeater 150 mph blower that i need to replace the small and large fuel lines. Do both lines go to the bottom of the tank? does it matter which nipple the large hose goes onto? At the moment the...


Both lines do go to the bottom of the tank. One is the supply line (has in-tank fuel filter on it) and the other is the fuel return line (only needs to be in the tank for 1/2" or 1". It does matter which nipple on the external primer bulb the lines connect to. One sucks in and one pushes out. If you push on it with your finger covering one of the nipples, it is easy to tell if it is sucking or pushing. It will make a little pop, when you remove your finger if it is sucking. Here is the lowdown.
The small diameter line out of fuel tank (has filter in-tank on end) connects directly to the side of the carburetor that has the fuel pump....that is the cover without the hole in it. Other larger diameter fuel line out of tank connects to the longer nipple on the external purge/primer bulb. The bulb "pulls" fresh fuel from the fuel tank to the carb and then out of the carb to itself, where it then "pushes" any air/old fuel back into the fuel tank. The remaining larger diameter fuel line in this setup goes from the metering chamber (has cover with writing on it and a vent-hole) side of the carburetor to the smaller nipple on the purge/primer bulb. Again, on the primer bulb, the longer nipple has a line going directly from it to the tank. This is the return line. The shorter nipple on the bub has a line from it going to the metering chamber side of the carb. If the purge/primer bulb is on top of the carb...small line from carb body to small hole in tank with filter. Larger diameter line goes from the bulb on the fuel pump side of the carb to the larger hole in the fuel tank where sometimes the line is held in place with a nylon nipple connector that keeps the line from pulling out of the tank. Otherwise, the line should enter the tank for 1/2" or so.

Jan 07, 2011 | Craftsman 25cc Gas Line Trimmer

1 Answer

Not shore wat side of carb hose gets filter large hose or small hose? The larger hose goes too the pump side and the small hose goes to the other side?


Small gas line goes thru fuel tank and has the in-tank fuel filter on it and connects to the outlet on the BODY of the carburetor. The other larger line goes from the Purge?Primer bulb on top of the carburetor to the larger hole in the fuel tank and is only a fuel return line. The fuel filter holds the small line in the tank and a small nylon connector holds the larger line in the tank or it can just be pushed thru 1/2-3/4" or so and it will stay in place.

Aug 29, 2010 | Poulan Garden

4 Answers

I need info on a Poulan Pro 445 fuel line routing


I'm so confused. This is reported as a Poulan and McCulloch pole saw, which one? Is it a pole saw? That is the only 445 Poulan I can find. It is reported as an electric but has a fuel routing problem.

If it is a Poulan Pro gas pole saw it is here: PP445 Gas Pole Pruner
The fuel system routing is terrible, but it is all there is.
Fuel Routing follows:
Tank to carburetor (hose in tank with filter on free end)
Carburetor to primer (primer draws fuel from the tank through the carb)
Primer to fuel tank (returns any excess fuel to tank when pushed) HTH
Lou

Oct 11, 2009 | McCulloch 10" Electric Pole / Chain Saw

2 Answers

Replaced primer bulb and fuel lines, now it won't stay running


The smaller line is the supply to the carb. and should have the filter in the tank, with sufficient length to allow fuel pickup from the bottom of the tank.The larger line returns excess fuel and pressure to the top of the tank.By squeezing the bulb and watching the fuel lines you will be able to determine if you have them right on the carb.

Sep 27, 2009 | Poulan Featherlite Gas Blower, with Low...

2 Answers

Where does the duck valve go in a Poulan 2150 chainsaw? Iam trying to replace the fuel lines . Does it go in the fuel tank? I need a diagram of the fuel lines.


is your fuel cap missing the hold down that keeps it from falling out of the tank.if the keeper is missing from fuel cap, the valve goes in the cap.if the cap is together then it just sticks in the fuel tank hole in the top...... hope this helps,let me know.................

Jun 03, 2009 | Poulan Pro Chain Saw 46cc 20"

4 Answers

Poulan 2050 chainsaw. Fuel line routing. Replaced all fuel lines. Primer bulb is marked Tank and Carb side. Tank side is for larger line and runs into tank and fuel filter. Carb side is smaller diameter...


Replaced my fuel lines on poulan 2050 today. The large diameter line is a return line from the primer to the tank. The smaller diameter line is the supply line from the tank to the carb. You need to cut this line and run a second piece of small diameter line from the card to the primer. I'm not sure if it makes a difference which of the two stems on the carb is the inlet or outlet line. I used the top stem as the inlet, and connected the bottom stem to the primer. My chainsaw started right up. So I either got lucky or maybe it doesn't matter.

Apr 14, 2009 | Garden

Not finding what you are looking for?
Craftsman 25cc Gas Line Trimmer Logo

Related Topics:

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

Dean Gruber

Level 2 Expert

110 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...