Question about Kenmore 24032\24036 Top Load Washer

1 Answer

On the rinse cycle when the water is filling it does not stop by overflows.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

You have a problem with the load switch and thin hose that run from tub to the load switch

Posted on Jul 09, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 209 Answers

SOURCE: Washer water overflow.

i am a recently retired engineer of 20 years and this sounds like a blockage to start with, when you remove the lid you will find a round disc like object (pressure switch) with a thin pipe coming from it going down to the bottom end of the machine, this pipe as either come off or is blocked somewhere. drain the machine totally, clear out the pipes, make sure there are no damaged parts to the pipes, then make sure all are fitted properly, start the machine off again and watch for water level shutting off near the bottom of the door, start with the above, if this doesn't cover the fault there may be an issue with the timer or electrical fault elsewhere/? hope this helps, if so rate me please, thank you

Posted on Sep 13, 2007

  • 209 Answers

SOURCE: GE Washer overflows

washing machines of any make or shape have a level sensor, this normally consists of a thin pipe from the lower end of the machine (where there is water) normally enters the bottom of the outer drum casing, this thin rubber or thin plastic pipe goes up to the top of the machine just inside the casing, it leads into a "pressure switch" a circular disc object about 50 cms in diameter on average, also this has about 4 to 6 wires on it, this thin pipe becomes blocked not allowing air to be forced up the tube into the switch, not switching the machine water flow off when it gets to the correct level empty the machine, drain off the water, unplug the power supply, and clear out this pipe, normally its congealed old soap powder, place pipe back as it was, checking for any leak holes in it, if damaged, replace it with new, run machine again to test long winded but i hope i have explained it thoroughly

Posted on Sep 27, 2007

  • 1073 Answers

SOURCE: Washer continuously fills but drains at the same time during rinse cycle.

you have the drain pipe too low into tthe house drain pipe, raise the washers drain pipe up , you only need four inches down into the hous drain

also the house drain pipe needs to be as high as the lid of the machine before you put the washer drain tube into the house drain

you have a syphoning effect

Posted on Apr 20, 2008

Illeagle
  • 525 Answers

SOURCE: Washing Machine won't stop filling up

Try resetting your water level control. If that doesn't help then set the water level control to the lowest setting and observe if level exceeds that setting. If so, you may possibly have a faulty water level control, or an obstruction in the air dome or water level control hose. This can be a tricky 1 to diagnose for a novice.

Posted on May 24, 2008

marka19
  • 1430 Answers

SOURCE: Kenmore Heavy Duty 80 Series Extra Capacity Plus

The problem is the pressure switch has failed or the hose is plugged up, has a hole in it. These are usually inexpensive and are very easy to replace. Here is a video this will walk you thru testing and replacing a pressure switch. You can also enter your model # for diagrams and illustrations of your specific model. All parts come with installation instructions. Not all models are available.

Posted on Oct 30, 2010

Testimonial: "I had already figured this out before viewing this message. I found that the pressure hose had fallen off of the water level pressure switch."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cold water won't stop before rinse cycle


if it fails to stop running only at the rinse part of the cycle it is probably in the timer as the solenoid valve has to cut the water off when the washer fills for the wash cycle too. fills for wash cycle and cuts off water, washes and drains, refills for rinse cycle and water just keeps running? does this every time you run it? that's in the timer. bad solenoid (water inlet valve) would keep running even on wash fill up. hope this helps.

Feb 25, 2014 | LG WM2688H Front Load Washer

2 Answers

Washing machine is overflowing in the rinse cycle


the front panel comes off,i think there is 2 screws on the front bottom,if not there should be spring clips in the top front seam on on each side,check the clear hose going to the tub,make sure nothing is in it and it is on tight,check the other side of the hose is behind the head panel,do the same there,if they both go good then you have a bad water level switch,let me know

Apr 23, 2009 | Washing Machines

1 Answer

GE SpaceMaker washing machine does not stop filling.


try replacing your water selenoid coming in. remember it isnt a mechanical timer it is a computerized timer, so if the selenoid isnt the problem, it might be the computerized timer. computers are very finicky, pain in the a- -!

Mar 23, 2009 | GE WSM2480DWW Unitized Spacemaker Washer...

1 Answer

Kenmore washer overflows during rinse cycle.


SOME OF THESE MACHINES HAVE TWO PRESSURE SWITCHES IN THEM, ONE FOR THE MAIN WASH WATER LEVEL AND ONE FOR THE RINSE WATER LEVEL. CHECK FOR A PLUGGED AIR PRESSURE HOSE FIRST AND THEN CHECK THE PRESSURE SWITCHES.

Jan 27, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Water keeps filling!!


sphion effect while the water comes in the water goes out ..because you never said that it overflows,,,so just put your drain hose up the height of the machine before it can go down,,,drain hose to low...onthejob

Nov 16, 2008 | Frigidaire FTF530FS Front Load Washer

2 Answers

Asko 10505 overflow problem


Replace the water valve and your problem is gone.

May 26, 2008 | Washing Machines

1 Answer

Washing machine filling


turn the power off if the water stops it most likley a pressure switch problem or the pressure tube on the side of the outer tank may have pulled off.if you turn the power off and the water doesnt stop then the valve is faulty (cold)if it was on the rinse.hope this helps.

Mar 17, 2008 | Admiral AW22 Top Load Washer

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2122 Answers

fordexpert

Level 3 Expert

5495 Answers

Mike Carew

Level 3 Expert

969 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...