Question about GE JKP45 Electric Double Oven

1 Answer

F2 message when self cleaning

I was using my self clean on our GE profile oven for the first time. After it ran for about 30 minutes, it started beeping and flashing F2. won't stop when I hit clear so I cut the power. What does this F2 mean?

Posted by on

1 Answer

Re: F2 message when self cleaning

I have the exact problem, had a service man look at it while still under warranty. He said it was fixed and left. Tried it again, same problem. Called him back 2 times after that, he quit responding to my calls. By tyhen warranty expired and GE refused to do anything.

Posted on Dec 16, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Tried to do self cleaning on oven, about 10 minutes in got "f2 locked door" and it won't clean. what is that all about?

Error code F2 on clean cycle is indicating that the maximum permissable cleaning temperature has been exceeded. (or it's got too hot!)

However it seems unlikely that that would happen in just 10 mins. more likely it is a problem with the oven temperature sensor which should be checked over as should the lock switches..

Dec 14, 2010 | GE JRP24 Electric Double Oven

1 Answer

GE JTP56 double oven controls OK top OK bottom no heat

have you inserted the business card as described in the solutions?

Jun 26, 2009 | GE Profile JTP56 Electric Double Oven

1 Answer

Self-clean turns off after 5 minutes with F2 error message

Hi MaryB,

F2 error code means that the oven temperature is too hot. You will have to replace relay board if faulty. Check and replace oven temperature sensor (RTD). If failure repeats, replace ERC (electronic range control or clock).For replacement part you may contact Sears at 1-800-252-1698; M-F 6:30 AM-10:30 PM - Sat 7:00 AM-9:30 PM - Sun 7:30 AM-9:30 PM - All times Central.

Hope this helps.

Thank you for using FixYa.

Apr 15, 2009 | Thermador C272 Electric Double Oven

1 Answer

GE: E Profile Single Electric Oven Model: JSP40W0WJWW

First press and hold the cancel/off button for 10 seconds.
If that does not work you have a bad thermal switch due to excessive heat buildup. Possibly a bad fan motor.
The 2 thermal switches are located on top of the oven behind the control panel.

Mar 18, 2009 | GE Profile JTP18 Electric Single Oven

1 Answer

GE JT912-30 single wall oven "help" with F7 - F0 error

I have a double oven GE Profile. The error message FO appeared. I shut off the circuit breaker for 30 minutes or more and the oven works but without warning FO reappears. FO message means there is short in the clear Off touch button. The only solution replace the complete panel. My cost delivered $328. Ouch!

Jan 19, 2009 | GE Profile JKP56 Electric Double Oven

1 Answer

Self-Clean gets too hot on JTP56 double-oven

Your husband is correct, kind of. You should not try self clean again until you get the oven repaired. You have a temp sensor going out. I doubt that the oven actually got too hot, most likely the resistor in the sensor is failing as it heats up and giving a false temp reading.Since the lower oven was operating at the time, it is probably the sensor in the lower oven. Don't use it for baking until you get it repaired. It will go out completely and shut down both ovens. You should be able to get a new sensor for around $30 and they are not hard to replace.

The oven won't set your house on fire during clean mode if the cabinets were built with the correct air space and dimensions, but they do get very hot, about 800 degrees F. Most ovens give no trouble during the clean cycle, but if there is any weak components in the electronics system it will show up then. It will give you less trouble over time if you don't use the self clean mode and just manually clean it.

Jan 18, 2008 | GE Profile JTP56 Electric Double Oven

6 Answers

GE: JTP56 F2 Door Locked displayed

I have the the same problem as discribed above. Does you oven fan go on for a long time after you use your oven during regular baking. Mine seems to stay on for 45 minutes after I bake anything. Can this be all tied together with the f2 problem? I am wondering if it is not just a fan circulation problem?

Dec 15, 2007 | GE Profile JTP56 Electric Double Oven

Not finding what you are looking for?
GE JKP45 Electric Double Oven Logo

1,339 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

8795 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers


Level 3 Expert

6993 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides