Question about Pride Mobility Products Pride Victory 10 - Three Wheel

1 Answer

What does the 7 beep code mean on my Pride Victory 10 scooter mean when I turn the key on ?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 313 Answers

This is a speed pot or throttle control problem (wig-wag) have you had some speed issues with the scooter before this happened, if so the wig-wag needs replacing. Make sure it is in the centre position at rest and switch the scooter on again.

Posted on Nov 25, 2014


6 Suggested Answers

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 175 Answers

SOURCE: my pride IV scooter will not start I get a click

An 8-flash code indicates that the controller has shot craps. The controller is located under the shroud beneath the seat by the batteries and it controls all of the power and automatic functions of the scooter. They are damaged most often by water infiltration like running through deep puddles, etc. or by over-amping the scooter by driving it through unstable terrain like sand, mud, wet grass. There's no fix for it but a replacement and it's pricey...several hundred dollars.

Posted on Aug 28, 2009

  • 25 Answers

SOURCE: I have a pride Victory 4 wheel scooter. Ran great

possibly burnt one of the motor brushes, you can remove the brush, and clean the face of the brush or put new brushes in

Posted on Sep 15, 2009

  • 26 Answers

SOURCE: Where can I find a schematic for a pride victory 10

try mobility centre penge
0208 676 0944

Posted on Apr 15, 2010

  • 280 Answers


Hi Fred,

Good job on replacing the batteries!
With the go go scooter, a beep code of 5 indicates a solenoid brake trip. This means that the brake manual/freewheel lever may be in the freewheel position. This means that you can push the scooter. Remove the key and push the freewheel lever to the drive position. Restart the scooter and the code should be cleared and the scooter will run. Hope this helps.

Posted on Jan 20, 2011

  • 692 Answers


check the freewheel lever on th rear of the chair near the right rear wheel if you can push the scooter easily then you are in freewheel locate the lever and move it to the drive mode and try to drive the scooter again if it still won't move then you have other problems that can only be checked by a service tech Hope this helps

Posted on Feb 27, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Turn on. Won't go. Six beeps. What's wrong?

hi ring pride 1-800-800-8586 about youre problem It could b a fault with youre control box ......good luck

Nov 29, 2015 | Pride Mobility Products Pride Victory 10 -...

1 Answer

Scooter is saying error code 8 which is motor does anyone know what this could be please?

Pride Mobility Products Victory 9 Scooter 4 Wheel Error code > ... > Pride Mobility Products Victory 9 Scooter 4 Wheel
Pride Mobility Products Victory 9 Scooter 4 Wheel, error code related issues. ... Question about Thermometer Mobility Scooters ... error code is 8 Error code 8 means an internal controller error or problem and requires replacement of the controller. ... Theysay there is no listing for code 9 I have replaced the batteries,checked .
Basic Troubleshooting Instructions - Pride Mobility > Resource CenterPride MobilityScooters. INFINFB2040 Sonic Troubleshooting ... Chargers. INFINFB2586 Charger Indicator Codes ... Disclosure Statement Pursuant to Cal. Civ. Code 1714.43(a)[PDF]Legend Owner's Manual - Pride Mobility Products

Nov 28, 2015 | Pride Health & Beauty

1 Answer


6 beeps =
Throttle lever (pot) is not in center position. Return throttle lever
to center position, then turn scooter OFF then ON.

Mar 07, 2015 | Pride Victory 10 3-Wheel

1 Answer

Pride victory 9 beeping 7 times won't Move

Go to Pride mobility web page and get the manual for your model . The codes and their meanings are described in the manual

Sep 23, 2014 | Health & Beauty

1 Answer

What does the 7 beep code mean on my Victory Pride 10 mean when I turn the key on ?

Hi , 7 bleeps is the throttle pot error , either a calibration problem or a faulty pot, i can help you , please contact me


Jul 11, 2014 | Pride Victory 4 Wheel Mid-Size Electric...

1 Answer

I have a 3 Wheel Pride Victory 10 Scooter. It has been beeping multiple times when turned on and it will not go forward. When I pull the lever just a little bit and then turn the key on it does work. The...

Hello, as a PDF File-SHOPRIDER SERVICE MANUAL 2007 1-800-743-0772. This is 36 pages,being you have a scooter you only need pages 1 to 18.19 to 36 covers wheelchairs.Download it to your Adobe reader,save & print for future ref.And good news the site i gave you[] is free,The job you need to to is quite easy as you will see,a tip though,take pics with ur mob,just to be sure in case you forget how things are,hope this has helped,im disabled myself & know what its like not to be moblie MERRY XMAS Colin.

Dec 16, 2010 | Pride Victory 4 Wheel Mid-Size Electric...

Not finding what you are looking for?
Pride Mobility Products Pride Victory 10 - Three Wheel Logo

649 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1367 Answers


Level 1 Expert

25 Answers


Level 3 Expert

85020 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides