Question about Onkyo TX-SR605 Receiver

1 Answer

What settings What setting should the receiver be at when watching Sky HD and when watching HD DVD.Thank you

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers
Re: what settings

What ever you want. the onkyo reciever allow you to select what input the hdmi inputs are assigned to.
you can assign DVD to hdmi 1, or 2, what ever you want.
Check the manual how to assign inputs.

Posted on Dec 13, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Watching Sky HD, sound ok in 5.1, then adverts

This is a problem with the digital lock.

What this means is that your receiver is suppose to sense the type of digital audio feed, during programming it receiver the 5.1 and decodes it, then the feed switches to a 2 channel signal and the receiver's DSP hangs up. I bet if you change inputs then change back it re-locks and works fine until the signal changes again.

This happened on some of the Harman receivers, I can't recall if the 130 had an RS-232 port on the back. If so you can go on and download a firmware update that may help with this problem.


Cover the basics, unplug and replug the receiver.

Second write down all your settings, perform a processor reset as outline in the back of your manual and reprogram the receiver.

I warn you if the update fails your receiver will not be worth repairing!!



Jan 27, 2010 | Harman Kardon AVR 130 Receiver

1 Answer

Don't want to use receiver to turn Plasma on via Verizon DVR

You can not have a signal from cable/satelite TV when reciever is OFF.The only way is reconnect by using defferent setup configuration to illiminate the receiver.In that case you well see just regular Tv program but you should connect antena to your TV.

Apr 17, 2009 | Onkyo TX-SR705 Receiver

1 Answer

NO AUDIO/set up problems

For this Sony, you have to use separate audio cable(s). Either optical in BD or Digital Audio in DVD (single coaxial cable will do the trick) I bet the display says UNLOCK. I had the same problem, very dumb.

Good day!

Jan 19, 2009 | Sony STR-DG510 Receiver

1 Answer

Onkyo TX SR 702 AV Receiver

don't run you video from the projector to the reciever. just run it to the dvd and run the sound from the dvd through the reciever

Jun 01, 2008 | Onkyo TX-SR702 Receiver

3 Answers

Denon Avr-588 setup


nice gear. Without further information, i am going to describe the best setup possible with your equipment.

1. make sure the speakers are connected to the receiver and you can hear sound out of it

2. connect cable box to receiver via hdmi to receiver.Choose cable on the receiver or video1 etc. (if you are not using hdmi cables post annd i will walk uthruogh a non hdmi process)

3. connect a hdmi cable from thee receiver monitor output area to the tv hdmi input

4. connect the dvd player hdmi to the input of the receiver

to watch select the tv av mode to line up with the receiver and choose video1 for tv and dvd to watch dvds on the receiver.

good luck


Jan 03, 2008 | Denon AVR588 Receiver

1 Answer

HDMI f/ dvd, dvr, receiver and tv

best set up if you have all hdmi is to have all your components go into the receiver ie. hd cable box, dvd etc. by using the hdmi output from the player(s) to the hdmi input to the receiver. next use one hdmi cable from the receiver to the tv then your laughing.

good luck


Dec 31, 2007 | Onkyo TX-SR605 Receiver

1 Answer

Set up Denon AVR 3806 to HD DVD player

Geesh! Finally found it in that encyclopedia of an instruction manual. If you have the manual, the solution is on page 63. If not, I'll provide an attached image below.

Dec 23, 2007 | Denon AVR-3806 Receiver

1 Answer

Audio & Video out of sync

Change the audio delay on your sky hd box in the sound settings

Oct 13, 2007 | Pioneer VSX-1016 Receiver

2 Answers

Surround sound from Sky +

Could be two things:

First you have to make sure the speakers are all active, there is a speaker button on the RXV361 front on the right I think but not on the remote, you need B setting for all speakers. You run the sound test from the set up menu.

or it could be that Sky is not showing the programme you are watching in 5.1 so you won't hear it from all speakers, you can force this by using the Music enhancer button of the RXV361 remote.

Hope that helps?

Sep 16, 2007 | Audio & Video Receivers

Not finding what you are looking for?
Onkyo TX-SR605 Receiver Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio & Video Receivers Experts

 Mike M
Mike M

Level 3 Expert

3320 Answers

D. E. Hev

Level 3 Expert

1059 Answers


Level 3 Expert

2963 Answers

Are you an Onkyo Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides