Question about Hotpoint Aquarius WF000 Front Load Washer
I went to the machine assuming the hot whites wash cycle had finished but found the 'mini load' and the 'rinse hold' LEDs were flashing on and off. The whites appeared to have been washed but not rinsed. I put the machine back onto the hot whites wash program again. Water briefly enters the machine before the same LEDs flash simultaneously again. The machine then empties itself of this water before it allows me to turn the on/off button to off and so stop the flashing of the LEDs. It was possible for me to put my whites through a spin cycle, but not a rinse and spin. Since then I have tried to run the machine empty on a normal colourfast cycle but the LEDs flash again shortly after a little water has entered the machine. Please help.
Best Solution posted on Sep 27, 2007 check the cold water supply, either from the mains pipe, there is no water getting into the machine, if water is there up to the machine check the solenoid for circuit, to do this unplug from electric, remove lid, and test the two wires on relevant solenoid, no circuit means faulty solenoid, (test with the 2 wires removed from solenoid) take care note position of wires to put back properly.
Comment by Pauleds, posted on Oct 22, 2007
Thank you for the easy to follow instructions in your reply. There is no problem with the water supply to the machine. The filters to the solenoid are clear and the solenoid checked out ok for circuit. Could you let me know if anything else could be the cause of the problem with my machine please.
Comment by Pauleds, posted on Nov 05, 2007 I have tried to run my machine again recently and have noticed some more symtoms of my machine. Although most of the time the two LEDs on my machine flash on and off within seconds of some water entering the machine, now and again the machine would go through some of the wash program, the LEDs would then activate when water is pumped out of the machine, during either of the rinse sequences. As the water is pumped out I have noticed that water rises through the plug hole of my sink to about 20mm high. I have checked the pressure switch to make sure it clicks and have also checked the pipe to it for blockages but they are ok. I found a small plastic peg (from a new shirt I think) next to the plastic ball in the sump, this probably affected the closure of the sump when water is pumped out of the machine which possibly prevented the correct pressure being attained a the right time during a program and so machine would not be able to activate the next sequence of the wash program? I then carried out a fast wash program with the machine empty, this went right to the end of the program successfully. My joy was premature though as with clothes in the machine the next wash only managed to get to the stage where the first load of is pumped out. I will check again the sump for more alien objects. If the sump and the pressure switch tube are not connected exactly the way they were before disconnection could that cause problems with the pressure switch? I have also found some slight brown marks on the 'Merloni' module circuit board (not sure if it is burned out as it is does not look bad). Could that possibly be the problem?
have an hotpoint aquarius washing machine. No. Wf210p.
We have recently fitted new drum bearings. After putting the machine together it starts to work for a short while and then it pumps the water out. As it starts to do this the on/off button flashes as well as the rinse hold. This continues for ever until the mains are switched off. Any ideas. This is driving us mad. Thanks.
Posted on Jun 12, 2008
Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.
Rate me pl.....if helped.
Posted on Jan 26, 2008
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Oct 18, 2012 | Hotpoint Aquarius WMA42 Front Load Washer
Nov 13, 2017 | Hotpoint Ariston Aquarius WD420 Front Load...
Nov 09, 2009 | Hotpoint Aquarius WF220 Front Load Washer
Nov 02, 2009 | Hotpoint Aquarius WF220 Front Load Washer
Oct 26, 2009 | Hotpoint Aquarius WF000 Front Load Washer
Dec 10, 2008 | Hotpoint Aquarius WF000 Front Load Washer
May 05, 2008 | Hotpoint Aquarius WF000 Front Load Washer
Sep 24, 2007 | Hotpoint Aquarius WF000 Front Load Washer
May 08, 2007 | Hotpoint Aquarius WF000 Front Load Washer
5,604 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: